Оценок - 2, средний балл: 3.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Auto Focus does 1)If the lens is dirty, clean it off. not focus properly. 2)The subject may not be in the center of the focus frame when you compose the image. 3)The subject you are shooting may not be a type that is compatible with Auto Focus (page 28). Use manual focus (page 64). 4) You may be moving the camera when shooting. Try shooting with Anti Shake or use a tripod. 5)You may be pressing the shutter button all the way without waiting for Auto Focus. Half-press the shutter button and allow enough time for Auto Focus to focus. Appendix 166 Problem Possible Cause and Recommended Action The subject is out of focus in the recorded image. The image may not be focused properly. When composing the image, make sure the subject is located inside the focus frame. The flash does not 1)If ? (Flash Off) is selected as the flash mode, change to fire. another mode (page 34). 2)If the battery is dead, charge it (page 15). 3)If a BEST SHOT scene that uses ? (Flash Off) is selected, change to a different flash mode (page 34) or select a different BEST SHOT scene (page 53). The ? (Flash Off) icon flashes red on the monitor screen and the flash does not fire. The flash unit may be malfunctioning. Contact a CASIO service center or your original retailer. Note that though the flash will not fire, you still can use the camera for non-flash shots. Camera powers down during Self- timer countdown. The battery may be dead. Charge the battery (page 15). The monitor screen image is out of focus. 1) You may be using Manual Focus and have not focused the image. Focus the image (page 64). 2)You may be using . (Macro) for scenery or portraits. Use Auto Focus for scenery and portrait shots (page 64). 3)You may be trying to use Auto Focus or ) (Infinity) when shooting a close-up shot. Use the . (Macro) for close ups (page 64). There is a vertical Shooting a very brightly lit subject can cause a vertical band to line in the monitor appear in the monitor screen image. This is a CCD screen image. phenomenon known as “vertical smear”, and does not indicate malfunction of the camera. Note that vertical smear is not recorded with the image in the case of a snapshot, but it is recorded in the case of a movie. There is digital 1)Sensitivity may have been increased automatically for a dark noise in images. subject, which increases the chance of digital noise. Use a light or some other means to illuminate the subject. 2)You may be attempting to shoot in a dark location with ? (Flash Off) selected, which can increase digital noise and make images appear coarse. In this case, turn on flash (page 34) or use lights for illumination. 3)Shooting with a high ISO sensitivity setting or with the Lighting feature can cause an increase in digital noise. Use a light or some other means to illuminate the subject. Appendix 167 Problem Possible Cause and Recommended Action A recorded image 1)Camera power may have been turned off before the save was not saved. operation was complete, which will result in the image not being saved. If the battery indicator shows , charge the battery as soon as possible (page 17). 2)You may have removed the memory card from the camera before the save operation was complete, which will result in the image not being saved. Do not remove the memory card before the save operation is complete. Though available lighting is bright, the faces of people in the image are dark. Not enough light is reaching the subjects. Change the flash mode setting to < (Flash On) for daylight synchro flash (page 34), or adjust EV shift to the + side (page 80). Night shots come out bad. Use the following BEST SHOT scenes (page 53) when shooting at night. • Night Scene (for shooting night scenery only) • Night Scene Portrait (for shooting people against night scenery) Subjects are too dark when shooting images in a seashore or ski area. Sunlight reflected by water, sand, or snow, can cause underexposure of images. Change the flash mode setting to < (Flash On) for daylight synchro flash (page 34), or adjust EV shift to the + side (page 80). The focus frame Normally, turning off the camera while “Detect Smile” is does not appear on selected for Auto Shutter will cause the camera’s face detection the monitor screen. setting to change. You will need to change the face detection setting again after turn on the camera. You can tell the camera to remember the Auto Shutter setting by selecting “On” for the “Auto Shutter” power on default setting (page 78). Digital zoom 1)The digital zoom setting may be turned off. Turn on digital (including HD zoom (page 77). zoom) does not 2)Date stamping may be turned on, which will cause digital work. The zoom zoom to be disabled. Turn off date stamping (page 143). bar indicates zoom 3)Digital zoom is disabled when the “White board, etc.” BEST only up to a zoom SHOT scene is selected. Select another scene (page 53). factor of 3.0. Appendix 168 Problem Possible Cause and Recommended Action When shooting Auto Shutter may not trig...