Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
2. Select the “Set Up” tab, select “Format” and then press [6]. 3. Use [8] and [2] to select “Format” and then press [SET]. IMPORTANT! • Formatting a memory card that already has snapshots or other files on it, will delete its contents. Normally you do not need to format a memory card again. However, if storing to a card has slowed down or if you notice any other abnormality, re-format the card. • Be sure to use the camera to format a memory card. Formatting a memory card on a computer and then using it in the camera can slow down data processing by the camera. In the case of a microSD or microSDHC memory card, formatting on a computer can result in non-conformity with the SD format, causing problems with compatibility, operation, etc. Turning the Camera On and Off Pressing [ON/OFF] (Power) turns power on and enters the REC mode. Pressing or holding down [p] (PLAY) turns on the camera and enters the PLAY mode. Pressing [p] To turn power on [ON/OFF] (Power) (PLAY) again switches to the REC mode. Back lamp • The back lamp lights green momentarily when you turn on the camera. • The Sleep function or Auto Power Off (pages 144, 145) will turn off power automatically if you do not perform any operation for a preset amount of time. To turn off the camera [p] (PLAY) Press [ON/OFF] (Power). Quick Start Basics 22 Attaching a Protector Attaching a Protector The camera comes with two protectors. Attaching one of the protectors helps to protect the side of the camera against damage if it is dropped. . About the screws that come with the camera The camera comes with a total of six screws: four long screws for attaching a protector, and two short screws. The short screws are extra replacements for the screws that are in the holes in the side of the camera when a protector is not attached. 1. Remove the two short screws from the holes on the lens side of the camera. • Store the short screws in a safe place where they will not become lost. 2. Attach one of the protectors and secure it in place with the two long screws. • The camera comes with a total of four long screws for attaching the protector. Two are required for installation and the other two are spares. IMPORTANT! • Use a commercially available precision screwdriver (#0) to loosen and tighten the screws. • Never attempt to loosen or remove any other of the camera’s screws except those specifically noted above. • Whenever a protector is not attached to the camera, be sure to fill the two holes on the lens side with the original short screws or the two extra short screws that come with the camera. Quick Start Basics 23 Holding the Camera Correctly Holding the Camera Correctly Your images will not come out clearly if you move the camera when you press the shutter button. When pressing the shutter button, be sure to hold the camera as shown in the illustration below, and keep it still by pressing your arms firmly against your sides as you shoot. Holding the camera still, carefully press the shutter button and take care to avoid all movement as the shutter releases and for a few moments after it releases. This is especially important when available lighting is low, which slows down the shutter speed. Horizontal Vertical NOTE Hold the camera so the flash is above the lens. • Take care that your fingers and the Flash strap do not cover any of the areas Front lamp indicated in the illustration. • To protect against accidentally Lens dropping the camera, attach the wrist strap and make sure it is Microphone around your fingers or wrist while you are operating the camera. • Never swing the camera around by its strap. • The supplied strap is intended for use with this camera only. Never use it for any other purpose. Strap Quick Start Basics 24 To shoot a snapshot To shoot a snapshot 1. Press [ON/OFF] (Power) to turn on the camera. Make sure R is on the display. If it isn’t, see page 58. Snapshot mode icon Monitor screen Shutter button [ON/OFF] (Power) Remaining Snapshot Memory Capacity (page 173) 2. Point the camera at the subject. You can zoom the image, if you want. Zoom button w Wide Angle z Telephoto Quick Start Basics 25 3. Half-press the shutter button to focus the image. When focus is complete, the camera will beep, the back lamp will light green, and the focus frame will turn green. Focus frame Back lamp Half-press Press lightly until the button stops. Beep, beep (Image is in focus.) When you half-press the shutter button, the camera automatically adjusts exposure and focuses on the subject it is currently pointed at. Mastering how much pressure is required for a half-press and a full-press of the shutter button is an important technique for good- looking images. • The focus frame in the screen shots included in this manual is shown at .. Note that you can change the form of the focus frame, if you want (page 78). 4. Continuing to keep the camera still, press the shutter button the rest of the way down. This records the snapshot. Shooting a Movie Press [0] (Movie) to s...