Оценок - 3, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Also, when the overall image is lacking in contrast, the camera will automatically correct the image for a sharper impression when shooting. Choose [i-Contrast]. . Press the nbutton, choose the 4 tab, and then choose the [i-Contrast] menu item. Press the qr buttons to choose [Auto]. • @ will appear on the screen. Under some conditions, the image may appear coarse or may not be corrected properly. You can correct recorded images (p. 110). Red-Eye Correction You can automatically correct red-eye that occurs in images taken with the flash. Choose [Flash Settings]. . Press the nbutton, choose [Flash Settings] from the 4 tab and press the m button. Adjust the setting. . Press the op buttons or turn the A dial to choose [Red-Eye Corr.] and press the qr buttons to choose [On]. • OE will appear on the screen (p. 44). Red-eye correction may be applied to red areas other than red eyes. For example, when red make-up has been used around eyes. • You can correct recorded images (p. 111). • With the flash raised, if you press the rbutton and immediately press the n button, the Flash Settings screen will appear. 91 Adjusting the Flash Exposure Compensation Just like with exposure compensation (p. 67), you can adjust the exposure ±2 stops in 1/3-stop increments when using the flash. Choose ~. . After pressing the m button, press the opbuttons to choose ~. Make the setting. . Press the qr buttons or turn the A dial to choose the flash exposure compensation, then press the m button. • ~ will appear on the screen. To set the flash exposure compensation, choose [Flash Settings] (p. 91) from the 4tab, then choose [Flash Exp. Comp] and press the qr buttons to choose a setting (p. 48). Safety FE The camera automatically changes the shutter speed or aperture value when the flash fires to avoid overexposing and blowing out the highlights in the scene. In the 4 tab, if [Safety FE] in [Flash Settings] is set to [Off], the shutter speed and aperture value will not automatically adjust. Adjusting the Flash Output In D mode, you can choose 3 levels of flash output. Set the camera to D mode (p. 89). Choose the flash output. . After pressing the m button, press the opbuttons to choose ~. Make the setting. . Press the qr buttons or turn the A dial to choose an option, then press the m button. • To set the flash output, choose [Flash Settings] (p. 91) from the 4 tab, then choose [Flash Output] and press the qr buttons to choose a setting (p. 48). • In M and B modes, you can set the flash output if you choose the 4 tab, then [Flash Settings] and set the [Flash Mode] option to [Manual]. 93 6 Using Various Functions for Shooting Movies This chapter provides more advanced information than the “Shooting Movies” and “Viewing Movies” sections of Chapter 1. • This chapter assumes that the mode dial is set to E (Movie mode). 95 Changing the Image Quality You can choose between three image quality settings. Choose the image quality. . After pressing the m button, press the opbuttons to choose . Choose an option. . Press the qr buttons or turn the A dial to choose an option, and press the m button. • The setting will display on the screen. Image Quality Table Image Quality (Recording Pixels/Frame Rate) Content 640 x 480 pixels, 30 frames/sec. For shooting standard quality movies. 640 x 480 pixels, 30 frames/sec. LP The image quality will be lower than with , but you can record twice the length. 320 x 240 pixels, 30 frames/sec. Since the number of the recording pixels is smaller, the image quality will be lower than with , but you can record three times the length. Estimated Shooting Time Image Quality Shooting Time 2GB 8GB 16 min. 47 sec. 1 hr. 7 min. 6 sec. 33 min. 2 sec. 2 hrs. 12 min. 3 sec. 46 min. 33 sec. 3 hrs. 6 min. 4 sec. • Based on Canon’s testing standards. • Recording will automatically stop when either the clip file size reaches 4 GB or the recording time reaches approximately 1 hour. • Recording may stop even if the maximum clip length has not been reached on some memory cards. SD Speed Class 4 or higher memory cards are recommended. AE Lock/Exposure Shift In X mode, you can set the exposure or change it in 1/3 steps within a range of ±2. Focus. . Press the shutter button halfway to focus. Lock the exposure. . After releasing the shutter button, press the o button to lock the exposure. The exposure shift bar appears. . Press the o button again to release the lock. Change the exposure. . While watching the screen, turn the A dial to adjust the brightness. Shoot. Other Shooting Functions The following functions can be used in the same way as for still images. • Zooming in More Closely on Subjects (Digital Zoom) (p. 60) You can use the digital zoom, but the optical zoom cannot be used. If you want to shoot at the maximum zoom factor, you should adjust the optical zoom to the maximum before shooting. The sound of the zoom will be recorded. • Using the Self-Timer (p. 63) • Shooting Close-ups (Macro) (p. 67) • Adjusting the White Balance (p. 7...