Оценок - 4, средний балл: 4.3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Grid Lines Displays grid lines to divide the screen into 9 parts. Helps confirm the vertical and horizontal positioning of the subject. 3:2 Guide Helps confirm the print area for a 3:2 print.* Areas outside the printable area are grayed out. * Images are still recorded at the standard aspect ratio of 4:3. Both Displays both the grid lines and the 3:2 guide simultaneously. (Rec.) Menu [DISP. Overlay] [Off]*/ 1 [Grid Lines]/[3:2 Guide]/[Both]. See Menus and Settings (p. 19). * Default setting. The grid lines and 3:2 guide will not be recorded in the image. Movie Shooting Movie Shooting Shooting Mode The following movie modes are available. For information on the recording pixels and frame rate in each mode, refer to Recording Pixels and Frame Rates (p. 37). Standard You can select the recording pixels and frame rate and record until the memory card is full (when a super high-speed memory card is used, such as the recommended SDC-512MSH). The digital zoom can be used while shooting in this mode (p. 29). • Maximum Size: 4 GB/movie* Fast Frame Rate Shooting Use this mode to record fast moving subjects, such as in sports photography. • Maximum Clip Length: 1 minute Compact Since there are few recording pixels and also the data size is small, this mode is convenient for sending movies as e-mail attachments or when the memory card capacity is low. • Maximum Clip Length: 3 minutes • The recording time will differ according to the memory card used (p. 118). * Even if the size of the movie data has not reached 4 GB, recording may stop when a shooting time of 1 hour has elapsed. Depending on the storage capacity of the memory card and the speed at which the data is written, recording may stop before reaching 4 GB or 1 hour. 1 Select a movie mode using the or button. ..In mode, you can change the recording pixels and frame rate (p. 37). 35 2 Shoot. • Pressing the shutter button halfway automatically sets the exposure, focus and white balance settings. • Pressing the shutter button fully starts recording video and sound simultaneously. • During shooting, the recording time and [..Rec] appear on the LCD monitor. • Pressing the shutter button fully again stops recording. Recording will stop automatically under the following circumstances. -When the maximum recording time elapses -When the built-in memory or memory card becomes full ..You are recommended to use a memory card that has been formatted in your camera to shoot movies (p. 25). The memory card supplied with the camera may be used without further formatting. ..Be careful of the following while recording. -Do not touch the microphone (Basic Guide p. 1). -Do not press any buttons other than the shutter button. The sound that buttons make will be recorded in the movie. -The camera will automatically adjust the exposure and white balance to suit the shooting conditions during recording. Please note, however, that the sounds made by the camera automatically adjusting the exposure may also be recorded. • The focus and optical zoom settings remain fixed for subsequent frames at the values selected for the first frame. • Do not point the camera at the sun when shooting. QuickTime is required to play back movies (Data type: AVI/ Compression method: Motion JPEG) on a computer (Only Windows 2000). Changing Recording Pixels and Frame Rates (Movies) You can change the recording pixels and frame rate when the movie mode is set to (Standard). 1 FUNC. Menu * (Frame Rate)/ * (Recording Pixels). See Menus and Settings (p. 18). * Default setting. ..Use the or button to select a frame rate/recording pixels and press the FUNC./ SET button. Recording Pixels and Frame Rates Frame rates indicate the number of frames recorded or played back each second. The higher the frame rate, the smoother the appearance of motion. Shooting Recording Pixels Frame Rate (frames/sec.) Standard 640 x 480 pixels – ..*1 • 320 x 240 pixels – • • Fast Frame Rate*2 320 x 240 pixels • – – Compact*2 160 x 120 pixels – – • *1 Default setting. *2 The recording pixels and frame rate are fixed. ..See Image Data Sizes (Estimated) (p. 119). ..See Memory Cards and Estimated Capacities (p. 117). 37 can be joined into a single several adjacent images The overlapping seams of can be joined into a single several adjacent images The overlapping seams of Stitch Assist can be used to shoot overlapping images that can later be merged (stitched) to create one panoramic image on a computer. Shooting Panoramic Images (Stitch Assist) Shooting Mode panoramic image. 1 Use the or button to select a shooting direction. • You can select from the following two shooting directions. -.. Left to right horizontally -• Right to left horizontally 2 Shoot the first image in the sequence. • The exposure and white balance are set and locked with the first image. 3 Compose the second image so that it overlaps a portion of the first and shoot. ..You can press the or button to return to the previously recorded image to retake the shot. ..Minor discre...