Оценок - 4, средний балл: 3.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Note that improper use may damage the equipment. • Do not insert a “Memory Stick Duo” without a Memory Stick Duo adaptor into “Memory Stick” compatible equipment, as this may cause equipment trouble. Note on using “Memory Stick PRO” (not supplied) • “Memory Stick PRO” with a capacity up to 1GB have been confirmed to operate properly with this camera. Additional information On Nickel-Metal Hydride batteries Effective use of the battery • Battery performance decreases in low- temperature surroundings, and the battery life is shortened under such circumstances. To use the battery longer, we recommend you keep the battery in its case in a pocket close to your body to warm it, and insert it in your camera just before you start shooting. • If you set [LCD LIGHT] to [OFF], the battery will run for a longer amount of time. • If you shoot a lot using the flash, the battery power will be used up faster. • We recommend having spare batteries handy for two or three times the expected shooting time, and try test shooting before actually using the camera. • Do not expose the battery to water. The battery is not water-resistant. Battery life • The battery life is limited. The battery capacity decreases little by little as you use it more and more, and as time passes. When the battery operating time seems to have been considerably shortened, a probable cause is that the batteries have reached the end of their life. • The battery life varies depending on storage, operating conditions, and environment, and is different for each battery. On the battery charger On the O-ring • Do not charge any other batteries except Sony Nickel-Metal Hydride batteries in the battery charger supplied with your camera. If you try to charge any other type of battery (e.g., manganese batteries, alkaline dry cells, primary lithium batteries, or Ni-Cd batteries) than the batteries specified, those batteries may leak, overheat, or explode, causing the danger of burns or other injuries. • Do not charge fully charged Nickel- Metal Hydride batteries again. Otherwise, there is a danger of leaks, excessive heat, explosions, or electric shock. • When charging a high capacity battery other than the supplied battery using the supplied battery charger, the full capacity of the battery may not be available. • When the CHARGE lamp flashes, this may indicate a battery error or that batteries other than the specified type have been inserted. Check that the batteries are the specified type. If the batteries are the specified type, remove all the batteries, replace them with new ones or another ones and check if the battery charger operates correctly. If the battery charger operates correctly, a battery error may have occurred. • The battery charger is not waterproof. Do not allow the battery charger to become wet. O-rings are a type of waterproof packing that is used in underwater cameras and watches, diving equipment, etc. This camera uses an O-ring in the waterproof cover portion. O-ring mating surface O-ring Before use Before using this camera underwater or in places exposed to water, be sure to inspect the O-ring and the O-ring mating surface. If the O-ring or the O-ring mating surface is cracked, scratched or otherwise damaged, or if sand particles, hair or other minute dirt has adhered, the waterproofing performance may be impaired. Note that water entering the inside of the camera may cause irreparable damage. Additional information Inspecting the O-ring and the O-ring mating surface Inspect the O-ring and the O-ring mating surface in a location that is free from sand, dust or moisture. a Before opening the waterproof cover, rinse off any sand and completely wipe away any water that may be present on the camera body. • Sand or water getting inside the camera may cause a malfunction. b Open the waterproof cover. • For details on how to open and close the waterproof cover, see page 12. c Inspect the O-ring and the O- ring mating surface. • Be sure to wipe away any dirt, sand particles, hair, dust, salt, lint or other foreign matter adhering to the O-ring with a soft, lint-free cloth. Even a single hair adhering to the O-ring may cause a water leak. Dirt Sand Hair Dust Salt Lint • Tiny dirt particles that are difficult to see may have adhered to the O-ring, so inspect the O- ring by running it through your fingers. • When wiping away dirt from the O-ring, take care that cloth fibers do not remain on the O- ring. • When it is difficult to wipe away the dirt from the O-ring, remove the O-ring and wash it with water. • Be sure to replace the O-ring with a new one if it becomes cracked, warped, crushed, twisted, split, scratched, rough or otherwise damaged. Crack Warp Crush Twist Split Scratch Rough d Close the waterproof cover. e Lock the lock switch. Removing/Setting the O-ring When removing the O-ring for replacement, cleaning or inspection, take care for the following points. If there is mud on the O-ring, or if the camera has been in seawater, be sure to rem...