Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
Note r The front fence might be fixed by screw. F Make sure that the front fence is aligned with the size line on the base of the paper tray. G Remove the two green screws on the rear fence as shown. H While holding in the green release laver, align the rear fence to the new paper size. I Check that the rear fence is set in the correct position. Make sure that the holes in the base of the paper tray are properly aligned with the holes in the rear fence. J Fix the rear fence with the two screws you removed in step G. K While squeezing in the sides of Changing the Paper Size 41 1 the side fence, lift it out. L Replace the side fence so that it matches the new paper size. Important r Make sure the tags at the bottom of the side fence are properly inserted. M Prepare the new paper, then insert it under the left and right metal tabs as shown. Fan the paper stack and insert it with the side you wish to point onto face-up. Important r Do not load a stack of paper that exceeds the limit mark. Limitation r You can set up to 250 sheets in the main paper tray. N Gently return the paper tray to its original position. Changing the Paper Size in the Optional Paper Supply Unit A Pull the paper unit fully out until it stops, then lift it out with both hands. B Remove the paper. B4 A4 14 11 Getting Started C Adjust the dial to match the paper E While squeezing in the sides of size. the side fence, lift it out. 1 A4 A4 Important . If the dial does not match the size of loaded paper, parts of printed images may be missing and paper jams could occur. D While holding in the green release lever, adjust the front fence to match the new paper size. Note . The front fence might be fixed by screw. FReplace the side fence so that it matches the new paper size. Important . Make sure the tags at the bottom of the side fence are properly inserted. G Prepare the new paper, then insert it under the left and right metal tabs as shown. Changing the Paper Size Fan the paper stack and insert it with the side you wish to print onto face-up. Important . Do not load a stack of paper that exceeds the limit mark. Limitation . You can set up to 500 sheets in the paper unit. H Gently return the paper supply unit to its original position. Getting Started 1 44 2. Sending a Fax Message Overview Overview The basic procedure to send a fax message is: A Set your document. B Dial the number. C Press the {Start} key. The rest of this section describes these steps and the various features that are available in more detail. There are two ways to send a fax message: • Memory Transmission • Immediate Transmission Check the indicators on the operation panel to check which mode is currently active and press the {Transmission Mode} key to toggle between them. Sending a Fax Message Memory Transmission In Memory Transmission mode, after you press the {Start} key, the machine doesn't dial the destination until all pages of your fax message have scanned into memory (in contrast with Immediate Transmission, where the number is dialed first and pages are scanned and sent one by one). Memory Transmission is useful because: • You can take your document away from the machine without having to wait too long • While your message is being sent, other people can use the machine • You can send the same message to more than one destination in a single operation. This technique is referred to as Broadcasting. Important . If there is a power failure, the power switch is turned off, or the plug is pulled out for more than 1 hour, all files stored in memory are deleted. As soon as power is restored, the Power Failure Report is printed to help you identify deleted files.. P.178 “When Power is Turned Off or Fails” Limitation . If memory is full (0% appears on the display), Memory Transmission is disabled. In this case use Immediate Transmission instead. Note . Maximum number of Memory Transmission files: 250 (1,000 when the optional Function Upgrade Card is installed) . Maximum number of destinations per Memory Transmission: 250 . Combined total number of destinations that can be stored: 500 (2,000 when the optional Function Upgrade Card is installed) . The number of pages that you can store in memory depends on the original document images and the scan settings. You can store up to 160 standard pages (ITU-T No.1 chart, Resolution: Standard, photo mode: off). . As default, the machine will return to the default transmission mode (Memory Transmission) after every transmission. You can change this so that the current mode is maintained. . P.236 “Changing the User Parameters” . You can expand the amount of memory available for storing documents by installing either of the following options: • 2M Expanded Memory Card: Up to about 320 pages. • 4M Expanded Memory Card: Up to about 480 pages. • 40M Expanded Memory Card: Up to about 1,200 pages. • 40M Expanded Memory Card and Function Upgrade Card: Up to about 3,000 pages. . The maximum number of fax numbers you can dial with the number keys ...
Эта инструкция также подходит к моделям:Факсы - 9980 (2.07 mb)