Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
If you forget to change the Recording Paper Size setting in Fax Parameter No. 23 when different paper is loaded in the cassette, the unit will Stop printing after the 1st page of an Incoming Fax and display a "PAPER SIZE MISMATCH ADJUSTING PAPER SIZE" error. Then, the Recording Paper Size setting automatically adjusts to the proper size and the unit resumes printing the Incoming Fax from the 1st page. 21 Installing YourMachine Connecting the Telephone Line Cable and Power Cord Power Cord Plug one end of the power cord into an ordinary 3 prong AC outlet and the other end into the receptacle on the rear of the machine. Warning: This apparatus must be properly grounded through an ordinary 3 prong AC outlet. Do not break off the earth (ground) prong to fit a 2 prong outlet. Power Cord (Included) Telephone Line Cable Plug one end of the telephone line cable into the "RJ-11C" telephone jack supplied by the telephone company and the other end into the LINE jack on the left side of the machine. RJ-11C Telephone Jack Telephone Line Cable (Included) 1. Your machine uses little power and you should keep it ON at all times. If the power is turned NOTE OFF for too long, the clock contents may be lost. Connecting the Telephone Line Cable and Power Cord External Telephone (Optional) You can connect an additional standard single line telephone to the machine. To connect the telephone, cut off the protective tab on the TEL jack. 23 Installing YourMachine Setting the Dialing Method (Tone or Pulse) Your machine can operate with either of two dialing methods (Tone or Pulse), depending on the type of telephone line you are connected to. If you need to change the dialing method to Tone or Pulse, follow the procedure below. 1 2 3 4 5 7 4 0 6 1 for “PULSE“. or 2 for “TONE“. SET MODE (1-8) ENTER NO. OR .. FAX PARAMETER(01-99) NO.=. 06 DIALING METHOD 2:TONE 06 DIALING METHOD 1:PULSE or 06 DIALING METHOD 2:TONE 1. For some countries, this feature is not available depending on the country’s regulation. The NOTE display may not show this feature. Adjusting the Volume You can adjust the monitor and ringer volume on your machine. The built-in speaker enables you to hear the dial tone, dialing signals, and busy tone. The ringer sounds when your machine receives a call. Setting the Monitor Volume 1 1 * MONITOR * . You will hear the dial tone through the speaker. 2 MONITOR VOLUME LOW [........] HIGH repeatedly to raise the volume. or MONITOR VOLUME LOW [ ] HIGH repeatedly to lower the volume. 3 Setting the Ringer Volume 1 1 Standby 2 repeatedly to raise the volume. or MMM-dd-yyyy 15:00 00% RINGER VOLUME (((( $ )))) RINGER VOLUME $ repeatedly to lower the volume. 3 1. You can also adjust the volume of the key touch tone and the volume of the buzzer in the Fax NOTE Parameter No. 10 (KEY/BUZZER VOLUME). (See page 36) 25 Installing YourMachine User Parameters General Description Your facsimile machine has several basic settings (User Parameters) to help you keep records of the documents you send or receive. For example, the built-in clock keeps the current date and time, and your LOGO and ID Number help to identify you when you send or receive documents. Setting the Date and Time At standby the display will show the date and time. Once the standby display is set, it will automatically be updated. 1 2 3 7 1 4 4 Enter the new date and time. Ex: 0 3 1 2 2 0 0 5 1 5 0 0 Month: March Date : 12th Year : 2005 Time : 3:00 PM If you make a mistake, use or to move the cursor over the incorrect number, then overwrite it with a correct one. 5 SET MODE (1-8) ENTER NO. OR .. 1:USER PARAMETERS? PRESS SET TO SELECT DATE & TIME .1-01-2001 00:00 DATE & TIME 03-12-2005 15:00 1. The clock of your machine is equipped with D.S.T.(Daylight Saving Time) system. So, your NOTE clock will automatically set the time forward from 2:00 AM to 3:00 AM on the first Sunday of April and set the time back from 2:00 AM to 1:00 AM on the last Sunday of October. If your state does not use the D.S.T. system, change the Fax Parameter No. 35 (DAYLIGHT TIME) to "Invalid" . (See page 38) 2. The current Date & Time must be set because it is required by the Telephone Consumer Act of 1991. (For details, see FCC NOTICE at the end of this Operating Instructions) User Parameters Setting Your LOGO When you send a document, your LOGO appears on the top of the copy printed out at the other station. The LOGO helps to identify you to someone who receives your document. 1 2 3 7 1 repeatedly until display shows; 4 4 Enter your LOGO (max. 25 characters and digits) by using the Character keys. Ex: P A N A S O N I C If you make a mistake, use or to move the cursor one space beyond the incorrect character, press CLEAR then re-enter the new character. If more than 19 characters are entered, the left side characters will scroll off the display. 5 SET MODE (1-8) ENTER NO. OR .. 1:USER PARAMETERS? PRESS SET TO SELECT LOGO . LOGO PANASONIC. 1. Your Company Name or your name must be set as your LOGO because ...