Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Note: If batteries are preinstalled, remove orange battery tab. 2. Remove chime cover. Use a small screwdriver to pry the cover tabs away from chime base and remove cover (see Figure 2). Note: To remove the cover after base is mounted, firmly grasp cover and pull. 3. Install 3 alkaline “D” batteries. Make sure batteries are oriented properly (see Figure 3). Chime Cover Tab (x4) Horizontal Keyhole Vertical Keyhole Mounting Holes Figure 2 - Back of Chime Type “D”Type “D”Type “D” Chime Volume Chime Volume Jumpers Figure 3 - Inside Chime © 2008 HeathCo LLC 598-1000-07 598-1000-07 -2- 4. Test range. Temporarily position chime and push button where you want it mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. 5. Adjust volume control. Adjust volume control to desired volume (see Figure 3). 6. Mount push button. Use either screws or double sided tape to mount push button. • Screw Mounting: To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver (see Figure 1). Note: Remove material in screw holes (if needed) before mounting with screws. Attach back of case to door jamb or wall (see Figure 4). Snap front of push button on. • Tape Mounting: When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. 7. Mount chime. Determine mounting location. The chime base can be mounted in two different ways. The base can be mounted using one keyhole and one mounting hole or two mounting holes. The base may be mounted horizontally or vertically depending upon the specific model purchased. Keyhole Mounting: • Remove batteries from chime. • Drill one 7/32" diameter pilot hole for keyhole wall anchor and insert anchor. Note: Keyhole slot is located about 1" (25 mm) from top of chime. • Mount keyhole screw to wall leaving about 1/8" (3 mm) of the screw threads exposed (see Figure 5). • Using keyhole on back of chime base, hang base on screw. • Level chime base. • Using the horizontal slot located in the bottom of the battery compartment, mark location for second screw. • Drill one 7/32" diameter pilot hole for wall anchor and insert anchor. • Insert second screw through the horizontal slot and attach to wall. • Verify chime is level and tighten screws securely. • Replace batteries (see Figure 3). • Snap cover onto chime as shown in Figure 7. Figure 4 598-1000-07 -3- Note: Chime shown mounted horizontally. Note: Chime shown mounted vertically. Screw Mounting Holes Keyhole Slot (Vertical Mounting) Keyhole Screw Figure 6 - Inside Chime Keyhole Slot (Horizontal Mounting) Screw Mounting Holes Figure 5 - Back of Chime Figure 7 Tune Settings Your wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected chimes). The factory setting is for the Ding-Dong tune (or Westminster, when available). This tune can be changed by following the instructions below. • Ding (one note tune) Inside Push Button: Add a jumper to location 8. • Ding-Dong (two note tune) Inside Push Button: Remove jumper from location 8. Inside Chime: Remove jumper from location 8. • Westminster (Eight note tune) (Available on selected chimes) Inside Push Button: Remove jumper from location 8. Inside Chime: Add a jumper to location 8. Note: All models have both front and back door tune capabilities. We recommend the back door use the Ding tune and the front door use the Ding-Dong tune (or Westminster tune, available on selected chimes). Models that include two push buttons will come factory set for front and back doors. Decals on the rear of the push button will indicate its setting. Chime Volume 1 2 3 4 5 6 7 8 1 2 3 4.5 6 7 8 Tune Setting (Not used on all models) Tune Setting Inside Chime Inside Push Button Note: Some models might require the use of tweezers to remove and replace the jumpers. Figure 8 Troubleshooting A. Chime does not sound: • Make sure push button and chime codes are the same (see Figure 9). • Check orientation of push button and chime batteries. (See diagram inside push button and chime for correct battery orientation.) • Check charge of push button and chime batteries, replace if necessary. B. Chime sounds when not intended (false triggers): Chime is receiving interference from another wireless device; change the code setting (see Code Setting below). C. Batteries seem OK, but the chime does not work when installed: • Do not mount chime or push button on metal or near metal studs. This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to move chime or push button off metal surface. • Concrete floors may reduce range. Move chime away from floor. • Try locating chime closer to push button. D. Code Setting: It is recommended to only change one code position at a time and then check to see if system is functioning properly. 1. Open the cases and locate the jumpers on both the push button and chime (see Figur...