Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
• Battery powered push button - No wires to run. • 128 selectable codes allow more than one chime system in the same house. • LED lighted push bar (see Lighted Push Bar Feature). Lighted Push Bar Feature This ACE® wireless push button contains a LED (Light Emitting Diode) that will illuminate in dark conditions so the push button will be more visible for your guests. This (patent pending) technology and built-in photocontrol will allow the light intensity of the push button LED to increase as the outdoor light conditions around the push button decreases.The actual time and intensity that the LED is visible will depend on the specific mounting environment of the push button. In nominal conditions the batteries will typically last 2 years. © 2007 598-1227-01 1. Install two lithium type CR2032 3 volt batteries (included). Remove back of case by pushing in tab on bottom with a small screwdriver. Make sure battery is oriented properly (see page 5). 2. Set the push button jumpers to match the chime receiver code. See “Code and Tune Setting” section. 3. Test range. Temporarily position push button where you want it mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. 4. Mount push button. Use either screws or double sided tape to mount push button. • To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver. Attach back of case to door jamb or wall. Snap front of push button on. • When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. -2- 598-1227-01 Code and Tune Settings Code Settings Note: Most installations will not require you to change any jumpers on your chime and push button. WARNING: Disconnect chime unit from power source before opening code access door. Close door and replace screw before reconnecting to power. The push button and chime communicate by using a code that can be changed by removing and/or adding jumpers on both the push button and chime. The code is factory set; however, there are 128 selectable codes that allow you to expand your system and prevent outside interference. Other wireless products may cause interference and the system may not function properly. Follow the instructions below for setting a new code. 1. Unplug wireless chime (if applicable). 2. Open the cases and locate the jumpers on both the push button and chime (See illustration on page 5). . The push button and chime both have eight different jumper locations. The jumper positions 1 through 7 are used for setting the code. 4. To change the code, add and/or remove jumpers as needed. It is recommended to only change one jumper at a time and then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for both the push button and chime for this system to function. 598-1227-01 - Tune Settings Your ACE® wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected chimes). The factory setting is for the Ding-Dong tune (or Westminster, when available). This tune can be changed by following the instructions below. • Ding (one note tune) Push button: Add a jumper to location 8. • Ding-Dong (two note tune) Push button: Remove jumper from location 8. Chime: Remove jumper from location 8. • Westminster (Eight note tune) (Available on selected chimes) Push button: Remove jumper from location 8. Chime: Add a jumper to location 8. Note: All models have both front and back door tune capabilities. You may purchase any ACE® wireless push button for a second entrance. We recommend the back door use the Ding tune and the front door use the Ding-Dong tune (or Westminster tune, available on selected chimes). Models that include two push buttons will come factory set for front and back doors. Decals on the rear of the push button will indicate its setting. -4- 598-1227-01 Note: Some models might require the use of tweezers to remove and replace the jumpers. Remove screw to open access door CR2032 + 1 2 3 4 5 6 7 812 45678 Inside Push Button * Code Settings 1-7 Must Match Both Push Button and Chime Tune Setting (Not used on all models) Back of Chime Tune Setting Replacing Push Button Batteries Install two lithium type CR2032 3 volt batteries. Insert Batteries (+) Positive Side Up. 598-1227-01 -5 Troubleshooting Chime does not sound: • Make sure push button and chime codes are the same (See pages , 4, and 5). • Check orientation of push button battery (See page 5). • Check charge of push button and chime batteries (if applicable), replace if necessary. Batteries seem OK, but the chime does not work when installed: • Do not mount chime or push button on metal or near metal studs.This reduces the transmitter range. Use 1/4" to 1/2" (6 to 1 mm) wood shims to move chime or push button off metal surface. • Concrete floors may reduce range. Move chime away from floor. •...