Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Keep these notes in a safe place for future reference. Checking Pack Contents Unpack your chime kit and identify the following parts: •Chime • Wall mounting bracket • Bell push • Bell push/converter/extender • Door contacts • 2x CR2032 battery for bell push and converter • 4x mounting screws for door contacts • 4x mounting screws for push/converter • 2x mounting screws for chime • 2x wall anchors • 2x adhesive pads • Bell wire (for use with converter and door contact) • Self-adhesive icons You will need: • 3x LR6 ‘AA’ Alkaline batteries • Phillips screwdriver • Small flat bladed screwdriver • 1/4-in. (6 mm) masonry drill Safety Before proceeding with the installation, please note the following safety warnings: • Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc. • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt. Quick Start The bell push supplied with this kit is pre-programmed to operate with the chime. Youneed to do the following to get started: • Open the bell push • Fit the push battery • Fit the chime batteries • Check the volume setting When you operate the bell push, the chime will sound and the 1st icon will flash. If you use the converter, an additional push or you want to assign a differenticon to your push, you will need to follow the Programming Procedure. • Open the bell push/converter/extender • Connect the push/converter/extender to the door contacts • Fit the push/converter/extender battery • Follow programming procedure to program push/converter/extender to the chime When the door contacts (a normally closed circuit) are separated/opened the alert will sound and the icon assigned to the converter will flash. • Mount the door contacts to the door and door frame. • Mount the push/converter/extender near the door frame. Open the Bell Push Insert a flat bladed screwdriver into the slot A at the base of the push. Carefully lever the cover and base apart (Fig. 1). M27199 A Fig. 1 Fit the Push Battery Insert the CR2032 coin cell. Ensure the face marked ‘+’ is uppermost (Fig. 2). M27153 CR2032 + CR2032Fig. 2 Fit the Chime Batteries To remove the chime battery cover, press at point B and slide the cover back 1/4 in. (5 mm), then lift off. Insert 3 x LR6 ‘AA’ alkaline batteries (not supplied). Observe polarity as marked inside the battery compartment (Fig 3). M27200 B Fig. 3 69-2139EFS—1 1 Installation instructions–RCWL301A Sliding Window Release the catch (B) and slide open the window (Fig. 4). M27201B Fig. 4 Volume Control The volume control is behind the sliding window on the front of the chime. Initially, set the control to mid-point. After you have tested your system, adjust to the desired volume (Fig. 5). M27202 VOLUME CONTROL Fig. 5 Use of Icons In addition to the chime sounds, your chime has a visual indication to show which device has activated it. An icon will illuminate when the chime is activated by the bell push, the converter or another compatible device. The chime supports 3 icons. MAIN BACK ALERT DOOR DOOR SYMBOL The ‘Main door’ and ‘Back door’ icons are usually used for bell pushes. The other iconis intended for use with other compatible devices, such as the door contacts. Icons numbered 1 to 3 are also included. The Icons are self-adhesive, supplied in strips of 3. They can be changed, if required, by opening the sliding window of the chime and gently peeling off the strips. If desired, the strips can be cut into individual icons and attached to the chime in a different order. Use the Programming Procedure to change the icon associated with a push. Programming Procedure Learn Procedure To enable your chime to learn the identity of your transmitter: • Press the button on top of the chime and keep it pressed. Each Icon will light in turn. When the Icon you want is lit, release the button. • While the Icon you have selected is lit, operate your push. The chime will sound. The Icon will flash. Unlearn Procedure If you want to remove a push from the chime’s memory: • Press the button and keep it pressed. • Each Icon will light in turn. When the Icon associated with the push to be unlearned is lit, release the button. • Press and hold down both & buttons, until a ‘beep’ sound is heard. Changing the Tune Operate the push. While the Icon is flashing, press the button. Press the button again and the tune will change. Repeat until the tune you want plays. Recall Function A short push of the button will flash the Icon that was last in use. Chime Sounds To hear the chime sounds without operating the bell push, press the button. Press the button again and the tune will change. Mount the Push Mount using either the double-sided adhesive pad or the screws provided. (See Fig. 6). Test your push before mounting. Avoid mounting to metal structures. M27155 TOP Fig. 6 69-2139EFS—1 2 Installation instructions–RCWL...