Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
Illuminated bell push buttons can be used when the chime is powered by a transformer (Honeywell RCA900N). Safety Before proceeding with the installation, please note the following safety warnings: • Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc. • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt. • Chime is for indoor use only. • Avoid mounting location which can expose chime to splashing or dripping liquid. • Use UL approved transformer for connection to mains. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like; danger of damage if battery is incorrectly replaced. Replace only with the same or equivalent type. Checking Pack Contents • Chime • 2 x fixing screws for chime • 2 x wall plugs You will need: • Wired push • 20 AWG minimum bell wire • 4 mm cross-head screwdriver • A small flat bladed screwdriver • 1/4-in. (6 mm) masonry drill bit • 4 x LR14 ‘C’ Alkaline batteries OR transformer (16V 10 VA) Honeywell part number RCA900N Installation 1. Open the chime cover M27275 Power Supply 2. Determine the type of power supply and type of wired push required to suit your installation. Use 4 x LR14 ‘C’ size alkaline batteries; OR a 16V, 10VA transformer as recommended in the table below below: TATTENTION! ATTENTION! 1216 V~ .ATENCION! M272763 Mount the Chime 3. Mounting holes are marked with a screw symbol. 2 M6 FTM27250 .... 120V~16V~ C3C216V~ C1V/ACAC321120V~ 16V~ 16V~ x 1M27279x 3OPTION 1: AC POWEREDDO NOT USE BATTERIES Wiring Connect the wires from door push and transformer (where used) to the chime terminals as detailed in step 4. The wires can be surface mounted or direct from opening in the wall and enter the rear of the chime housing using the wire guide channels provided. 4a. Transformer powered - Wiring for standard/lighted push via a 16V 10VA transformer. 120V~ 16V~ C3C216V~ 120V~ C1V/ACAC321x 1M27280x 3OPTION 2: SERIES AC CONNECTIONREQUIRED BATTERIES Note: Wire/cable length should not exceed 150 ft. (50 m). 4b. Battery powered - Wiring for standard (non-lighted) push only. Note: Wire/cable length should not exceed 150 ft. (50 m). x 1C3C2C1V/ACAC321M27281x 3 Operate Push 5. Chime will play the default tune. The associated channel LED will illuminate. M27277 6. To adjust volume. To Change Tune 7. Chime tunes are provided plus an additional alert tone. Tunes Table Ding Dong St Clements Westminster Tube Chime Warm Brass Fantasy ! Alert Press push button, chime will play tune, while the Channel LED on chime is flashing, press and release tune button . Press and release button again to cycle through the available tunes until you hear the tune you want to play. The last tune played will be stored after Channel LED stops flashing. To confirm, press the push button and chime will play tune you want. M27278! Program Button 8. The Program button can be used to: • Change the tune of the associated push without pressing the push button. Press and hold the program button l. The channel LED will illuminate in sequence. Release the program button when channel LED for the related push illuminates. The chime will play the latest tune, channel LED will flash. While channel LED is flashing, tune can be changed using the tune select button . • Recall A short push of the program button l will flash the Channel LED linked to the last push that was used. M27251 9. Clip on the front cover. 10. For customizable wood covers only: Choose your paint, wood stain/ varnish or wall paper and then apply to the cover. Follow manufacturers’ advice on the paint/vanish. It is possible to unscrew the four screws shown below for finishing. Ensure you screw it back with the same screws provided! Once completed, clip it onto the base. Specification Chime Operating Temperature 32°F to 104°F 0°C to +40°C Sound Level (typical) 90dBA @ 3 ft (1m) Power Supply 4 x LR14 C size alkaline batteries OR 16V 10VA transformer (UL approved) Honeywell part number RCA900N Battery Life (if applicable) (5 operations/day) 12 months Troubleshooting When the illuminated bell push is operated, very dim / no light appears on the push… Check the power supply. You should use a 16V 10VA transformer connection for an illuminated push. Follow step 4. The chime does not work… • Check that the wiring is done correctly according to step 4, using minimum 20AWG wire. If using batteries: • Check that the batteries are the correct type, LR14 ‘C’ cells. Only use alkaline batteries. • Check that the batteries are fitted correctly (with correct polarity). • Check that batteries are not too low. The chime does not sound… • Check that the volume control is not at the minimum setting. Low battery light flashes… • When the chime battery is low, an amber LED located at the side of the chime will flash. Install new batteries ...
Эта инструкция также подходит к моделям:Двери и окна - RCW35 (1.98 mb)