Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
All Rights Reserved. P-MU-DG25 Ver. D Publish:2010.08.12 Page: 1/ 3 GIANNI INDUSTRIES, INC Output 2 relays (Dry contacts: N.O./N.C./Com.) Relay Strike Time 01~99 seconds or Toggle Mode (00) / Relay 1 (*100) , Relay 2 (*200) Relays Electric Current 3A/120VAC , 3A/24VDC Relay Activation Time Strike Time: 1~99 seconds (adjustable) Strike mode: Access Timer or Latch Memory Volume 49+50 PIN codes Relay 1 is controlled by 001~049 user slots Relay 2 is controlled by 050~099 user slots EPROM Non-volatile memory, System will retain all programs and codes after a total loss of power. Finish Stainless steel brushed housing Ambient Humidity 0~95% relative humidity non-condensing Operating Temperature -20°C~+70°C 3. The indicator signal chart: Sound and LED indicator: LED signal Green LED Power on, stand-by Red LED Relay 1 activated Yellow LED Relay 2 activated Sound signal 1 Beep Effective PIN codes 2 Beeps Entering ' Exiting from the programming mode 3 Beeps Incorrect operation 5 Beeps Master Code reset to Factory default (12345) 4. Operation Instruction: ♦ Enter Program Mode: 1. Compose twice the master code (Factory default is r 12345 j ) ^ 2 beeps ^ you are now in the "program mode". 2. After 60 seconds if you have not entered any codes or data, the system will automatically exit from the programming mode. After 32 wrong codes attempts at , system the will be lockout for 60 seconds. ♦ Exit from the programming mode: 1. Press r#j to exit from the programming mode. ♦ Add PIN codes (at programming mode) Enter the slot position code r*001~*099 j ^????? Input 5 digit PIN code^ (beep) enrolled ^ (repeat) , or, Press r#j to exit from the programming mode. Note 1: The codes r 00000 j , r 12345 j or master code can not be used as PIN code. Note 2: Relay 1 is controlled by 001~049 user slots, Relay 2 is controlled by 050~099 user slots ♦ To Delete a User Code : (at programming mode) Press the slot position code of your choice to delete (example "006") ^Press r*006 j ^ r00000j ^ (beep) ^delete^Press r#j to exit from the programming mode. Copyright Gianni Industries, Inc. All Rights Reserved. P-MU-DG25 Ver. D Publish:2010.08.12 Page: 2/ 3 GEM GIANNI INDUSTRIES!, INC. ♦ To Program Relocking Timer (at programming mode) A. Relay 1 : Press r*100j (relay 1) or r*200j (relay2) , Followed by the number of seconds the relay should open^ r05j =5 seconds (01 ~99 = seconds) ^ (beep) ^enrolled ^ Press r#j to exit from the programming mode. Enter r00 j Sets the relay to latching mode. (Correct code entered opens the relay, and the relay stays open until the correct code is entered again). B. ♦ Changing the Master codes: (at programming mode) Enter r*000j Followed by the new 5 digit master code^ (beep) r#j to exit from the programming mode. »enrolled^Enter ♦ Master Code reset to Factory default r 12345 Insert the jumper P1^ 1-2 positions beeps^Reset successful. j 5. Wiring diagram: Note: ♦ It is suggested to use a linear powe...
Эта инструкция также подходит к моделям:Двери и окна - DG-26 (180.51 kb)