Оценок - 6, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. 2. Plug-in the doorbell chime. Chime Volume Control 1. Set the chime volume on the back of the plug-in chime, if desired. 3. Before mounting, test the doorbell range. Plug-in the chime where you want to mount it and temporarily place the doorbell button on the doorjamb. Press the doorbell button. Access Door Operation Press the doorbell button to verify that the Push doorbell and chime work properly. If the chime Button does not sound see the Troubleshooting guide on page 4. 4. Mount the doorbell button. Use either screws or double sided tape to mount Doorbell Button the doorbell button. To mount with screws, remove the back of the case by pushing in the tab on the bottom with a small screwdriver and rotating the blade. Attach the back of the case to the door jamb or wall. Snap the front of the button back on. When attaching the doorbell button using the double sided tape, make sure the surface of the door jamb or wall is clean. Code and Tune Settings Code Settings Note: Most installations will not require you to change any of the jumpers on your doorbell. WARNING: Disconnect chime unit from power source before opening code access door. Close door and replace screw before reconnecting to power. The doorbell button and chime communicate by using a code that can be changed by removing and/or adding jumpers on both the doorbell button and chime. The code is factory set; however, there are 128 selectable codes that allow you to expand your system and prevent outside interference. Another wireless doorbell system or other wireless products may cause interference and the system may not function properly. Follow the instructions below for setting a new code. 1. Disconnect the power to the doorbell button and chime. -2-595-5494-11 2. Open the cases and locate the jumpers on both the doorbell button and chime (See illustration). . The doorbell button and chime both have eight different jumper locations. The jumper positions 1 through 7 are used for setting the code. 4. To change the code, add and/or remove jumpers as needed. There are 128 different combinations. It is recommended to only change one jumper at a time and then check to see if system is functioning properly. Note: Jumpers in positions 1 through 7 must be exactly the same for both the doorbell button and chime for this system to function. Tune Settings Your Heath®/Zenith wireless doorbell has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note). The factory setting is for the Westminster; however, this can be changed by following the instructions below. • Ding (one note tune) Doorbell button: Add a jumper to location 8. • Ding-Dong (two note tune) Doorbell button: Remove jumper from location 8. Chime: Remove jumper from location 8. • Westminster (Eight note tune) Doorbell button: Remove jumper from location 8. Chime: Add a jumper to location 8. Note: Model 6167 has doorbell buttons for both front and back door. The back door must use the Ding tune and the front door may use either the Ding-Dong or Westminster tune. Remove screw to open access door * Code Settings 1-7 Must Match Both Doorbell Button and Chime Inside Note: Some models Doorbell might require the use of Button tweezers to remove and replace the jumpers. 12 45678 12 45678 Doorbell Button Battery Replacement Install an alkaline type A23 12 Volt battery. The positive terminal should be positioned as shown. Tune Setting Back of Chime 595-5494-11 - Troubleshooting Chime does not sound: • Make sure the doorbell button and the chime codes are the same (See pages 2 and ). • Check orientation of doorbell button battery (See page ). • Check the doorbell button battery, replace if necessary. Batteries seem OK, but the chime does not work when installed: • Do not mount the chime or doorbell button on metal or near metal studs.This reduces the transmitter range. Use 1/4" to 1/2" (6 to 1 mm) wood shims to move the chime or doorbell button off the metal surface. • Don't mount the chime too close to ground level concrete slabs. This may also reduce the range. Mount the chime away from the floor. • Try different locations for the chime closer to the doorbell button. Also try to orient the chime at a different angle to increase the range. The range of the doorbell depends on location, temperature and battery condition. Technical Service Please call 1-800-858-8501 (English speaking only) for assistance before returning product to store. If you experience a problem, follow this guide. You may also want to visit our Web site at: If the problem persists, call* for assistance at 1-800-858-8501, 7: 0 AM to 4: 0 PM CST (M-F).You may also write* to: HeathCo LLC P.O. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service * If contacting Technical Service, please hav...
Эта инструкция также подходит к моделям:Двери и окна - SL-6166 (115.11 kb)