Войти:
Оценок - 4, средний балл: 4 ( )

Инструкция по эксплуатации BEA, модель Bollards 10PBR45X

Производитель: BEA
Размер: 231.94 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


2. May adversely affect the safe and reliable performance of the product resulting in a voided warranty. 4 Pre Installation Check 1. When preparing to wire multiple devices together for a ‘system’ configuration, it is best to ensure the correct operation of each device independently before starting to help reduce troubleshooting time later in the event of a discrepancy. 2. Prior to installing any equipment, ensure correct line voltage and stability. When applying equipment on a new installation utilizing newelectrical supply circuits, always ensure correct line voltage exists and is stable. Remember to shut the power back off after this is checked and before performing any wiring to the system. 5 Installation 1 Hardwire Bracket - Optional FOR HARDWIRING RUN WIRE THROUGH 1” DIAMETER HOLE 2.19 in 55.58 mm 1/4-20 53.95 mm 2.12 in 3.65 in 25.40 mm 143.51 mm 5.65 in 0.44 in 11.11 mm 92.71 mm 1.00 in 39.37 mm 1.55 in 3.55 in 92.10 mm 1. The Bollard is designed to house a pushplate used to activate a door by either a remote controlled transmitter or hardwired directly to thedoor control. If the door is hardwired, pass the wire through the 1 inch diameter hole in the mounting bracket. 2 Attach Mounting Bracket Using Expansion Anchors - Existing Concrete 1. Mark and drill 3/8” diameter hole in fourlocations. 2. Hammer in and set anchor in four hole locations. 3. Install and tighten nuts to secure mountingbracket. Page 2 of 4 75.0131.05 20080606 5 Installation (Continued) 3 Attach Mounting Bracket Using ‘L’ Shaped Anchors - New Concrete 6” 1” EXPOSED 1. Pour concrete at least 6 inches deep. 2. Insert anchors into curing concrete. Leaveat least 1 inch exposed. 3. Once concrete has cured attach anchor and tighten nuts onto mounting bracket. 4 Attach Post to Mounting Bracket 1. Align post to mounting bracket and attach post to mounting bracket with four post mounting screws. 5 Install Pushplate PUSHPLATE INSTALLATION DUAL PUSHPLATE INSTALLATION PANTHER PUSHPLATE INSTALLATION 1. Thread the pushplate screws into the mounting box leaving a majority of the screw exposed. Attach the pushplate to the mounting screws, then use the hex key provided to fully tighten the screws. Refer to the appropriate Pushplate User’s Guide for detailed installation and setup instructions. 75.0131.05 20080606 Page 3 of 4 5 Installation (Continued) 6 Attach Transmitter TRANSMITTER MOUNTING TRAY NOTE: PANTHER PUSHPLATES DO NOT REQUIRE A TRANSMITTER. ATTACH TO PUSHPLATE ATTACH TRANSMITTER HERE CAUTION: IF THE TRANSMITTER IS ALLOWED TO HANG DOWN INSIDE THE BOLLARD, ERRATIC OPERATION MAY OCCUR. 1. If using the transmitter for this application, attach transmitter to mounting tray with velcro pad included in the package. Hardwired systems donot require this step. 2. Attach plastic cap to top of the post with three cap mounting screws. Tighten screws with hex key included in the pushplate package. Do not leave problems unresolved. If a satisfactory solution cannot be achieved after troublesh...

Эта инструкция также подходит к моделям:
Двери и окна - Bollards 10EMSQ475X (231.94 kb)
Двери и окна - Bollards 10PBS45X (231.94 kb)
Двери и окна - Bollards 10PBDGP1 (231.94 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории