Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit. 10 Connections Connections ips • Depending on your TV and other equipment you wish to connect, there are various ways you could connect the DVD+VCR. Use connections described on pages 11-13. • Please refer to the manuals of your TV, VCR, Stereo System or other devices as necessary to make the best connections. • For better sound reproduction, connect the DVD+VCR’s DVD/VCR AUDIO OUT jack to the audio in jacks of your amplifier, receiver, stereo or audio/video equipment. See Optional, Preferred TV Connections on pages 12-13. Caution • Make sure the DVD+VCR is connected directly to the TV. Tune the TV to the correct video input channel. • Do not connect the DVD+VCR’s DVD/VCR AUDIO OUT jack to the phono in jack (record deck) of your audio system. • Do not connect your DVD+VCR via your VCR. The DVD image could be distorted by the copy protection system. Connecting Antenna/Cable TV to DVD+VCR 1 11 Disconnect the antenna leads from the rear of the TV. 2 22 Identify the type of cable from your antenna. If it is a round cable as illustrated, it is a 75 ohm coaxial antenna cable. This cable will connect directly to the jack marked ANT.IN on your DVD+VCR. ip If your antenna lead wire is a flat type antenna cable, connect it to an Antenna Adapter (300-ohm to 75-ohm) (not supplied) and slip the Adapter onto the ANT.IN jack. The Adapter does not screw on to the DVD+VCR, it just slips over the jack. Antenna Antenna Flat Wire (300 ohm) 300/75 ohm Adaptor (Not supplied) Cable TV Wall Jack OR OR Without Cable Box If your cable wire is connected to your TV without a converter or descrambler box, unscrew the wire from your TV and attach it to the ANT.IN jack on the DVD+VCR. Use the supplied round coaxial cable to connect between the DVD+VCR’s RF.OUT jack and the 75 ohm antenna input jack on the TV. With this connection, you can receive all midband, super band, and hyperband channels. With Cable Box If a converter is required in your cable system, follow the instruction below: The cable hookup permits both TV and DVD+VCR operation. To view or record CATV channel 1 Tune the TV to the DVD+VCR output channel (CH 3 or 4). 2 Set the DVD+VCR channel selector to the output channel of the Cable Converter box by using the CH/TRK (v/V) or number (0-9) of your DVD+VCR. (Example: CH3) 3 Select the channel to view at the Cable Converter Box. otes • With this connection, you CANNOT record one program while viewing another. • If you are using a cable box to tune channels, it is not necessary to do Auto Channel Programming as indicated on page 15. Cable TV Wall Jack Back Panel of Typical Cable Box Rear of DVD+VCR PREPARATION Rear of DVD+VCR 11 Connections (Continued) Connections (Continued) Basic TV Connections • Make one of the following connections, depending on the capabilities of the equipment to be connected. RF coaxial connection Connect the RF.OUT jack on the DVD+VCR to the antenna in jack on the TV using the 75-ohm Coaxial Cable supplied (R). ote If you use this connection, tune the TV to the DVD+VCR’s RF output channel (CH 3 or 4). How to set the DVD+VCR’s RF output channel 1. Set the TV to the VCR channel (3 or 4) depending upon the selected channel. 2. When the DVD+VCR is turned off, press and hold CH (V/v) on the front panel for more than five seconds. It will turn itself on and “RF03” or “RF04” appears in the display window. 3. Press CH (V/v) on the front panel or CH/TRK (v/V) on the remote control to change the RF output channel (CH 03 or CH 04). 4. Turn off the DVD+VCR. Audio/Video connection 1 11 Connect the DVD/VCR VIDEO OUT jack on the DVD+VCR to the video in jack on the TV using the video cable supplied (V). 2 22 Connect the Left and Right DVD/VCR AUDIO OUT jacks on the DVD+VCR to the audio left/right in jacks on the TV (A1) using the supplied audio cables. ote If you use this connection, set the TV’s source selector to VIDEO. Rear of TV Optional, Preferred TV Connections ote You can ONLY watch and listen to DVD playback through the connections shown below. S-Video connection 1 11 Connect the S-VIDEO OUT jack on the DVD+VCR to the S-Video in jack on the TV using the optional S-Video cable (S). 2 22 Connect the Left and Right AUDIO OUT jacks of the DVD+VCR to the audio left/right in jacks on the TV using the supplied audio cables (A2). Component Video (Color Stream®) / Progressive Scan (ColorStream® pro) connection • ....If your television is a high-definition or “digital ready” television, you may take advantage of the DVD+VCR’s progressive scan output for the highest video resolution possible. • ....If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try Progressive Scan on the DVD+VCR. 1 11 Connect the COMPONENT/PROGRESSIVE SCAN VIDEO OUT jacks on the DVD+VCR to the corresponding in jacks on the TV using an optional Y Pb Pr cable (C). 2 22 Connect the Left ...