Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
No sound. • The equipment connected with the audio cable is not set to receive DVD+VCR signal output. • Select the correct input mode of the audio receiver so you can listen to the sound from the DVD+VCR. • The audio cables are not connected securely. • Connect the audio cable into the jacks securely. • The power of the equipment connected with the audio cable is turned off. • Turn on the equipment connected with the audio cable. • The AUDIO options are set to the wrong position. • Set the AUDIO options to the correct position. The playback picture is poor. • The disc is dirty. • Clean the disc. • The TV channels are not tuned in properly. • Check tuning, carry out tuning again. • Tape heads are dirty. • Clean video heads. • Tape is a rental or was recorded on another VCR. • Use PR/TRK (3/4) for manual tracking adjustment while tape is playing. REFERENCE 37 Troubleshooting (Continued) Symptom Cause Correction The DVD+VCR does not start playback. • An unplayable disc is inserted. • Insert a playable disc. (Check the disc type and Regional code.) • The disc is placed upside down. • Place the disc with the playback side down. • The disc is not placed within the guide. • Place the disc on the disc tray correctly inside the guide. • The disc is dirty. • Clean the disc. • The Rating level is set. • Cancel the Rating function or change the rating level. Video tape cannot be inserted. • Is the cassette compartment empty? • Eject the tape in. No Hi-Fi sound • Audio mode is not set properly. • Select STEREO by repeatedly pressing AUDIO on the remote control. No NICAM sound recording • NICAM mode is not set properly. • Make sure NICAM in the menu is set to AUTO for the station to be recorded. The remote control does not work properly. • There is an obstacle in the path of the remote control and this unit. • Remove the obstacle. • The batteries in the remote control are exhausted. • Replace the batteries with new ones. • The remote control is not pointed at the remote sensor of the DVD+VCR. • Point the remote control at the remote sensor of the DVD+VCR. • The remote control is too far from the DVD+VCR. • Operate the remote control within 23ft (7 m). • This remote control use the same buttons for VCR and DVD functions (ex.PLAY). • When using a VCR, first press the VCR button. When using a DVD, first press the DVD button. Timer recording is not possible. • Clock in DVD+VCR is not set to correct time. • Set clock to correct time. • Timer has been programmed incorrectly. • Reprogram Timer. • indicator light does not appear after programming timer. • Reprogram Timer and turn DVD+VCR off to enable timer. Specification General Power requirements AC 200-240 V, 50 Hz Power consumption 17 W Dimensions (approx.) 430 X 78.5 X 265 mm (w/h/d) Mass (approx.) 4.2 kg Operating temperature 5°C to 35°C (41°F to 95°F) Operating humidity 5 % to 90 % Timer 24 hours display type RF Modulator UHF 22-68 (Adjustable) System Laser Semiconductor laser, wavelength 650 nm Video Head system Double azimuth 6 heads, helical scanning. Signal system PAL Frequency response DVD (PCM 96 kHz): 8 Hz to 44 kHz DVD (PCM 48 kHz): 8 Hz to 22 kHz CD: 8 Hz to 20 kHz Signal-to-noise ratio More than 100 dB (ANALOG OUT connectors only) Harmonic distortion Less than 0.008% Dynamic range More than 100 dB (DVD) More than 95 dB (CD) Inputs (VCR) Audio -6.0 dBm, more than 10 kohms (SCART) -6.0 dBm, more than 47 kohms (RCA) Video 1.0 V (p-p), 75 ohms, unbalanced (SCART/RCA) Outputs (DVD) VIDEO OUT 1 Vp-p 75 ohms, sync negative Audio output (digital audio) 0.5 V (p-p), 75 ohms, RCA jack x 1 Audio output (analog audio) 2.0 Vrms (1 kHz, 0 dB), 600 ohms, RCA jack (L, R) x 1/SCART (TO TV) Outputs (VCR/DVD) Audio -6.0 dBm, less than 1 kohms (SCART) Video 1.0 V (p-p), 75 ohms, unbalanced (SCART) • Designs and specifications are subject to change without notice. REFERENCE Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. DTS and DTS Digital Out are trademarks of Digital Theater Systems, Inc. 39 Precautions When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both sides, on top and at the rear). When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly. Failure to heed the following precautions may result in damage to the unit, remote control or disc. 1. DO NOT place the unit — — in an environment prone to extreme temperatures or humidity. — in direct sunlight. — in a dusty environment. — in an environment where strong magnetic fields are generated. — on a surface that is unstable or subject to vibration. 2. DO NOT block the unit’s ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.) 3. DO NOT place h...