Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
• Connect the FM wire antenna to the FM antenna connector. otes • To prevent noise pickup, keep the AM loop antenna away from the Recorder Combi Receiver and other components. • Be sure to fully extend the FM wire antenna. • After connecting the FM wire antenna, keep it as close to horizontal as possible. FM Wire antenna (supplied) AM FM GND GND ANTENNA CONNECTOR SYSTEM FRONT R REAR R CENTER REAR L FRONT L SPEAKERS 4 4 4 4 4 HOOKUP 19 Connections (Continued) Connections (Continued) Assembling and Connecting to the Speakers (Front Speaker) The front speakers are detached from the speaker stands. Connect the speaker cables and assemble the front speakers from speaker stands as illustrated. How to connect the Speakers • ....Connect the speaker cables to the appropriate terminals on the bottom of each front speaker. • ....After connecting the speaker cabless to the appropriate terminals on the bottom of each front speaker and attach the front speakers to the speaker stands. To attach the speaker to the stand ote • ....You cannot detach the speaker from the stand after assembling the front and rear speakers. About Ferrite Core Be sure to attach the ferrite core to the System cable (for connecting to this unit). This ferrite core can reduce noises. How to attach the ferrite core 1 Press the stopper [a] of the ferrite core to open. 2 Insert the ferrite core on the System cable. 3 Close the ferrite core unit it clicks. ote • ....Attach the ferrite core near the unit (Refer to the fig.3 and comment.). The length here is short as much as possible. 20 Connections (Continued) Connections (Continued) Speaker System Connections Connect the SYSTEM on the Recorder Combi Receiver to the SYSTEM SELECTOR rear of the Active Subwoofer Speaker, using the supplied System cable. Connect the speakers using the supplied speaker cables. To obtain the best possible surround sound, adjust the speaker parameters (volume, distance, etc.). System cable otes • ....Be sure to match the speaker cable to the appropriate terminal on the components: + to + and – to –. If the cables are reversed, the sound will be distorted and will lack base. • ....If you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive output on the speakers. HOOKUP 21 Before Operation Before Operation Speaker Positioning In the case of normal position use the 6 speakers (2 front speakers, 1 center speaker, 2 rear speakers and sub- woofer). If you want to play the excellent bass sound, DTS digital surround or Dolby Digital surround, you should connect a subwoofer. • Front speakers According to your listening position set up the speakers for equal distance. And by hearing position set up the interval between speakers to 45 degree. • Center speaker The center speaker and front speakers are ideally the same height. But normally place it above or below the television. • Rear speakers Place left and right behind the listening area. These speakers recreate sound motion and atmosphere required for surround sound playback. For best results, do not install the rear speakers too far behind the listening position and install them at or above the level of the listener’s ears. It is also effective to direct the rear speakers towards a wall or ceiling to further disperse the sound. In the case of a smaller room size, if the audience is near to the rear wall set the rear speakers opposite each other, and set the rear speakers above 60 - 90 cm than the listener’s ears. • Subwoofer This can be placed in any front position. Subwoofer Center Speaker Front Speaker (Left) Rear Speaker (Right) Front Speaker (Right) Speaker Positioning Example 22 Before Operation (Continued) Before Operation (Continued) Mini Glossary for Sound Mode Allows you to enjoy 5.1(or 6) discrete channels of high quality digital audio from DTS program sources bearing the trademark such as discs, DVD and compact discs, etc. DTS Digital Surround delivers up to 6 channels of transparent audio(which means identical to the original masters) and results in exceptional clarity throughout a true 360 degree sound field. The term DTS is a trademark of DTS Technology, LLC. Manufactured under license from DTS Technology, LLC. The Dolby Digital surround format lets you enjoy up to 5.1(or 6) channels of digital surround sound from a Dolby Digital program source. If you play DVDs with “ ” mark, you can enjoy even better sound quality, greater spatial accuracy, and improved dynamic range. (II) Dolby Pro Logic II creates five full-bandwidth output channels from two-channel sources. This is done using an advanced, high-purity matrix surround decoder that extracts the spatial properties of the original recording without adding any new sounds or tonal colorations. MOVIE mode: The Movie mode is for use with stereo television shows and all programs encoded in Dolby Surround. The result is enhanced soundfield directionality that approaches the quality of discrete 5.1-channel sound. MUSIC mode: The Mus...