Оценок - 3, средний балл: 3.7
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
If your TV is listed in the table below, set the appropriate manufacturer code. While holding down TV POWER button, and press the manufacturer code for your TV with the numerical buttons (see the table below). Release the TV POWER button to complete setting. Manufacturer Code Number LG / GoldStar 1 (Default), 2 Zenith 1, 3, 4 Samsung 6, 7 Sony 8, 9 Hitachi 4 Depending on your TV, some or all buttons may not function on the TV, even after entering the correct manufacturer code. When you replace the batteries of the remote, the code number you have set may be reset to the default setting. Set the appropriate code number again. 7 Main Unit a bc a1 11 / I (POWER button) Switches the unit ON or OFF. bDisc Tray Insert a disc here. cOPEN/CLOSE (Z) Opens or closes the disc tray. dRemote Sensor Point the remote control here. eDisplay window Shows the current status of the recorder. REC: The recorder is recording. TV: Indicates when the recorder is in TV tuner mode. : Indicates when the recorder is in timer recording or a timer recording is programmed. : Shows the current status of the recorder. (clock, program number, etc). fN / X (PLAY / PAUSE) Starts playback. Pause playback or recording temporarily, press again to exit pause mode. d e fghi jk l gx (STOP) Stops playback or recording. hz (REC) Starts recording. Press repeatedly to set the recording time. iP/S (Progressive Scan) Switchs the progressive mode. 576i(OFF), 576p(ON) jUSB Port Connect an USB Memory Stick. kDV IN Connect the DV output of a digital camcorder. lAV IN 3 (VIDEO IN/AUDIO IN (Left/Right)) Connect the audio/video output of an external source (Audio system, TV/ Monitor, VCR, Camcorder, etc.). 8 9 AC IN~ C AC IN~ Hooking up the unit aAntenna connection Connect the Terrestrial TV antenna to the ANTENNA IN jack on the unit. bAntenna connection to your TV Connect one end of the RF cable to ANTENNA OUT jack on the unit and other end to ANTENNA IN jack on your TV. cSCART connection Connect one end of the scart cable into the AV1 SCART jack on the unit and other end to the corresponding in jack on your TV. You can get Audio and Video signals together with this connection. dPower cord connection Connect the mains lead to the AC IN terminal on the unit. Then plug the power cord into the mains. 10 Hooking up the unit - more you can do Component connection Connect one end of the component(Y PB PR) cable to the COMPONENT OUTPUT jack on the unit and other end to the COMPONENT INPUT jack on your TV. Connect one ends of the audio cables (red and white) to the analog AUDIO OUTPUT jack on the unit and other ends to the AUDIO INPUT jack on your TV. If your television is a high-definition or “digital ready” television, you may take advantage of the unit’s progressive scan output for the highest video resolution possible. If your TV does not accept the Progressive Scan format, the picture will appear scrambled with the progressive signal. Set the resolution to 576p using P/S button on the front panel for progressive signal. S-Video connection Connect one end of the S-Video cable to the S-VIDEO OUTPUT jack on the unit and other end to the S-Video INPUT jack on your TV. Connect one ends of the audio cables (red and white) to the analog AUDIO OUTPUT jack on the unit and other ends to the AUDIO INPUT jack on your TV. Digital audio connection Connecting to an amplifier/receiver, Dolby Digital/MPEG/DTS decoder or other equipment with a digital input. Connect one end of the digital audio cables (COAXIAL or OPTICAL) to the digital audio output jack (COAXIAL or OPTICAL) on the unit and other end to the digital audio input jack (COAXIAL or OPTICAL) on your amplifier. This recorder does not perform internal (2 channel) decoding of a DTS sound track. To enjoy DTS multi channel surround, you must connect this recorder to a DTS compatible receiver via one of this recorder’s digital audio outputs. AC IN~ AC IN~ AC IN~ Connecting a PAY-TV/Canal Plus Decoder You can watch or record PAY-TV/Canal Plus programmes if you connect a decoder (not supplied) to the unit. Disconnect the unit’s mains lead from the mains when connecting the decoder. You do not need to turn on the unit to view the signals from the connected tuner on your TV. SCART AV To watch or record PAY-TV/Canal Plus programmes, set [AV2 Connection] option to [Decoder] (see page 15) and set the program’s [Decoder On/Off] option to [On] on the Setup menu (page 13) If you disconnect the unit’s mains lead, you will not be able to view the signals from the connected decoder. Connecting to the AV2 DECODER jack Connect a VCR or similar recording device to the AV2 DECODER jack of this unit. You do not need to turn on the unit to view the signals from the connected tuner on your TV. To watch or record the source from AV2 DECODER jack, set [AV2 Connection] option to [Other Device] (see page 15) and set [AV2 Recording] option to [Auto], [CVBS], [RGB] or [S-Video] as required (see page 17). • Pictures containing copy protection signals t...