Войти:
Оценок - 4, средний балл: 4.3 ( )

Инструкция по эксплуатации Sony, модель DVP-S536D

Производитель: Sony
Размер: 1.05 mb
Название файла:
Язык инструкции:ensl
Перейти к скачиванию



К этому устройству также есть другие инструкции:

Фрагмент инструкции


x DTS Selects the DTS signals to be output via the DIGITAL OUT OPTICAL and COAXIAL connectors. • OFF: when the player is connected to an audio component lacking a built-in DTS decoder. • ON: when the player is connected to an audio component having a built-in DTS decoder. If the player is connected to an audio component lacking a built-in DTS decoder, do not set this. Otherwise, when you play the DTS sound track, a loud noise or no sound will come out from the speakers, affecting your ears or causing the speakers to be damaged. x 48kHz/96kHz PCM (DVD only) Selects the sampling frequency of the audio signal to be output via the DIGITAL OUT OPTICAL and COAXIAL connectors. • 48kHz/16bit: The audio signals of DVDs are always converted to 48 kHz/16 bit. • 96kHz/24bit: All types of signals including 96 kHz/24 bit are output in their original format. However, if the signal is encrypted for copyright protection purposes, the signal is only output as 48 kHz/16 bit. Notes • If you select “96kHz/24bit” when a receiver (amplifier) which cannot accept 96 kHz is connected to the player, no sound or a loud noise will come out from the speakers. • Even if you set “48kHz/96kHz PCM” in “AUDIO SETUP” to “96kHz/24bit,” the sampling frequency is converted to 48 kHz/16 bit when a VIRTUAL 3D SURROUND mode is selected. • The analog audio signals from the AUDIO OUT connectors are not affected by this setting and keep their original sampling frequency level. 58 Settings for the Speakers (SPEAKER SETUP) To obtain the best possible surround sound when you use the 5.1CH OUTPUT connectors, use the SPEAKER SETUP display to first specify the size of the speakers you have connected and their distance from your listening position. Then set the balance and level. Use the test tone to adjust the volume of the speakers to the same level. For speaker hookup instructions, see page 13. The default settings are underlined. Select “SPEAKER SETUP” in the setup display. SPEAKER SETUP SIZE: DISTANCE: BALANCE: LEVEL: OFFTEST TONE: FRONT: CENTER: YES LARGE(REAR) LARGE LARGE REAR: SUBWOOFER: To set, press , then . To quit, press . ENTER DISPLAY x SIZE Selects the size of the speakers to be connected. • FRONT — LARGE: Normally select this. — SMALL: When the sound cracks or the surround sound effects are difficult to hear, select this. This activates the Dolby Digital bass redirection circuitry and outputs the bass frequencies of the speaker from the subwoofer. • CENTER — NONE: If you do not connect a center speaker, select this. — LARGE: Normally select this. — SMALL: When the sound cracks, select this. This activates the Dolby Digital bass redirection circuitry and outputs the bass frequencies of the center speaker from other speakers . • REAR — NONE: If you do not connect a rear speaker, select this. — LARGE (REAR/SIDE): Normally select either of these according to the rear speaker’s position*. — SMALL (REAR/SIDE): When the sound cracks or the surround sound effects are difficult to hear, select either of these according to the rear speaker’s position*. This activates the Dolby Digital bass redirection circuitry and outputs the bass frequencies of the rear speaker from other speakers . • SUBWOOFER — NONE: If you do not connect a subwoofer, select this. This activates the Dolby Digital bass redirection circuitry and outputs the LFE signals from the front speakers as long as the front speaker size is set to “LARGE.” — YES: If you connect a subwoofer, select this to output the LFE (low frequency effect) channel from the subwoofer. * Rear speaker position Specify the location of the rear speakers for correct “VIRTUAL REAR SHIFT,” “VIRTUAL MULTI REAR” and “VIRTUAL MULTI DIMENSION” effects. These effects can be found in “VIRTUAL 3D SURROUND” of the Control Menu display. • SIDE: If the location of the rear speakers corresponds to section A in the illustration below. • REAR: If the location of the rear speakers corresponds to section B in the illustration below. This setting affects only the “VIRTUAL REAR SHIFT,” “VIRTUAL MULTI REAR” and “VIRTUAL MULTI DIMENSION” mode. 90° 20° AB45° BA Notes • The cut off frequency for the subwoofer is fixed at 120 Hz. • If your speakers are too small to reproduce low bass frequencies, please set all speaker settings to “SMALL” and utilize a subwoofer for low frequency sound. Settings 59 Settings and Adjustments Settings for the Speakers (SPEAKER SETUP) x DISTANCE The default distance setting for the speakers in relation to the listening position is shown below. 3.6m 3.6m 3.6m 3.0m 3.0m You can vary the distance of each speaker as follows. The default adjustments are in parentheses. Be sure to change the value in the setup display when you move the speakers. • FRONT (3.6m) Front speaker distance can be set in 0.2 meter increments from 1 to 15 meters. Distance is measured from the front speaker to the listening position. • CENTER (3.6m) Center speaker distance can be set in 0.2 meter increments. Place the center speaker directly...

Эта инструкция также подходит к моделям:
DVD-проигрыватели - DVP-S535D (1.05 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории