Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
10 EN Connect audio cables Route audio to other devices Connect the audio from this DVD player to the Route the sound from this DVD player to other TV to allow sound output through the TV. devices to enhance audio play. Connect to digital amplier/receiver 1 Connect the audio cables (not supplied) to the AUDIO OUT L/R sockets on this DVD player and the audio input sockets on the TV. 1 Connect a coaxial cable (not supplied) to the COAXIAL/DIGITAL OUT socket on this DVD player and the COAXIAL/ DIGITAL input socket on the device. Tip • You can optimise the audio output (see chapter ‘Adjust set tings’ - [ Audio Setup ] > [ Digital Audio ]) for details. AUDIO IN DIGITAL IN COAXIAL DIGITAL OUT Connect English EN 11 Connect to analogue stereo system Connect USB device AUDIO IN 1 Connect the audio cables (not supplied) to the AUDIO OUT L/R sockets on this DVD player and the audio input sockets on the device. Tip • You can optimise the audio output (see chapter ‘Adjust settings’ - [ Audio Setup ] > [ Analogue Output ]) for details. 1 Connect the USB ash drive to the (USB) socket on this DVD player. Note • This DVD player can only play/view MP3, WMA , DivX or JPEG les that are stored on such devices. • Press to access the content and play the les. Connect to power outlet Warning • Risk of product damage! Ensure that the power supply voltage cor responds to the voltage printed on the back or the under side of the DVD player. 1 Connect the power cord to the power outlet. The DVD player is ready to be set up for use. 12 EN 4 Get started Navigate through the menu 1 Point the remote control directly at the remote sensor on this DVD player and select the desired function. Prepare the remote control 1 Push to open the battery compartment cover. 2 Use the following buttons on the remote control to navigate through the on-screen 2 Insert two R03 or AAA batteries type with menus. correct polarity (+/-) as indicated. 3 Close the battery compartment. Button Action v V Move up or down. Caution Move left or right. b B • Remove bat teries if they are exhausted or if the remote control is not to be used for a long time. OK Conrm a selection. • Do not mix batteries (old and new or carbon and Enter numbers. alkaline, etc.). • Bat teries contain chemical substances, they should be disposed off properly. Get started English EN 13 Find the correct viewing channel 1 Press 2 to turn on the DVD player. 2 Turn on the TV and switch to the correct video-in channel. • You may go to the lowest channel on the TV, then press the Channel Down button on the TV remote control until you see the Video In channel. • You may press ° button repeatedly on the TV remote control. • Usually this channel is between the lowest and highest channels and may be called FRONT, A/V IN, VIDEO, etc.. Tip • See the T V user manual on how to select the correct input on the T V. • If the audio output of this DVD player is routed to other audio device (such as audio system or receiver), tur n on the audio device to the appropriate audio input channel. Refer to the device user manual for details. Select menu display language Note • You can skip this setting if this DVD player is connected to a HDMI CEC compliant T V. It switches automatically to the same OSD menu language as per your T V setting. 1 Press SETUP. • [ General Setup ] menu is displayed. 2 Select [ OSD Language ], then press B. Nederlands Auto Standby DivX(R) VOD Code OSD Language Disc Lock Sleep Timer General Setup Auto (Eng) English Francais Deutsch Italiano Espanol Portugues • The language options are different depending on your country or region. It may not correspond to the illustration shown here. 3 Press vV to select a language, then press OK. Tip • You can set the default language for DVD audio and disc menu, see chapter ‘Adjust set tings’ - [ Preferences ] for details. 14 EN Turn on Progressive Scan Connect a progressive scan TV with component video sockets (see chapter ‘Connect video cables - Option 2: Connect to component video sockets’ for details). 1 Turn on the TV to the correct viewing channel for this DVD player. 2 Press SETUP. 3 Press V to select [ Video Setup ]. 4 Select [ Component Video ] > [ Interlaced ], then press OK. 5 Select [ Progressive ] > [ On ], then press OK. • A warning message is displayed. 8 You can now turn on the progressive scan mode on the TV (see the TV user manual). Note • The progressive scan set ting will not be available when the HDMI video signal is detected. • During play, when progressive scan mode is on for both this DVD player and the T V, distor ted picture may display. Turn of f the progressive scan feature on both this DVD player and the T V. Get started English Video Setup Component Video Picture Setting TV Display TV System Progressive HD JPEG HDMI Setup On Off 6 To proceed, select [ OK ] and press OK. • The progressive setup is complete. Note • If a blank /distor ted screen is displayed, wait for 15 seconds for the auto recover. • If no picture displayed, tur ...