Оценок - 2, средний балл: 4.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Remove the battery compartment in the direction of the arrow. (Back of the remote control) Hole 1 2 Operating Range of Remote Control Unit Do not subject the remote control unit to strong vibration or shock. Keep the remote control unit free from moisture and water. • After battery replacement, your remote control unit may not work. If this occurs, remove the battery and re-insert in about 5 minutes. • It may be difficult to operate the remote control unit if the remote control sensor on the DVD player is exposed to direct sunlight or strong artificial light. Try operating the remote away from such light sources. Using the Remote Control Unit Important! Caution • Remove the battery when not planning to use the remote control unit for a long period of time. 2. Place the lithium battery in the battery compartment and put the battery compartment cover back on the remote. • Match the polarities (+ and -) on the battery with the marks in the battery compartment. If the battery is inserted in the wrong direction, your remote control may not work correclty. (Remote Control Sensor)2m(6.56ft) 30 30 Connecting Headphones to the DVD You can attach headphones with a stereo mini-jack plug to the PHONES jack for private listening. There are three jacks available. How to use headphones 1. Insert headphones into the A, B or C PHONES jack. • This jack is a stereo mini-jack. PHONES Important! • Turn the headphone volume down to the minimum setting before connecting. Caution • Once you connect headphones to the DVD, your DVD Player’s speakers will be disconnected. 2. Adjust the volume level by using the VOLUME control dial. 17 Connecting to an External Component (Input Select) You can enjoy video from your VCR or Camcorder on your DVD player. Important! • Always turn off the DVD Player and other components before you connect any cables. • Refer to owner’s manual of the components you are connecting for more information on those particular components. NOTE: • In the INPUT mode, the video input must be the standard PAL or NTSC. VCR or other component equipped with external output connectors 18 When connecting to an external component Jack/Plug Color Video: Yellow Audio (left): White Audio (right): Red To AUDIO OUT To VIDEO OUT Audio Cable Video Cable ENGLISH Viewing a Video from an External Component Use the procedure below to view a video from a VCR or Camcorder on your DVD player. To view a video from an external component 1. Connect the external component according to the procedure outlined on page 18. 2. Turn on the external component. 3. Turn on the DVD player. 4. Press the INPUT button to set the INPUT mode. 5. Press the PLAY button on the external component. Caution • Power is not supplied from this device to the connected DVD player. • When not using your DVD player, always remove all connecting cables from the video or audio input/output jacks. • If no signal is input for more than 5 minutes while in the input mode, this unit enters the standby mode. INPUT 19 to a TV equipped with an S-VIDEO input jack. 1. Turn on the TV. 3. Turn on the DVD player, and start playback. Caution Connecting to a TV to a TV equipped with an S-VIDEO input jack. 1. Turn on the TV. 3. Turn on the DVD player, and start playback. Caution Connecting to a TV Connecting to a Stereo Component You can enjoy high-resolution video using an S-VIDEO cable when connecting your DVD player When you connect the DVD player to an audio system, you can listen to higher quality sound. • Always turn off the DVD Player and TV before you connect any cables. ENGLISH 2-CH Audio Playback To view video with a TV Analog Connection 2. Press the TV/VIDEO button on your TV to select the input from the DVD player. Jack/Plug Color Jack/Plug Color Video: Yellow Audio (left): White Audio (right): Red Connect to a TV equipped with external connection jacks To AUDIO INPUT To VIDEO INPUT To S-VIDEO INPUT Audio Cable S-Video/VIDEO Cable Audio (left): White Audio (right): Red Audio Cable Audio Amplifier Connect to input jacks ANALOG INPUT (White) (Red) L R • If you wish to view video on your TV only, close the display panel of your DVD player. Playback will continue and audio to the speakers will be cut off, but you still will be able to use the remote to control the DVD player. • For power saving, press the LCD CON. button to power off the LCD display. 21 ENGLISH Playing Dolby Digital (5.1-CH) and DTS Audio Connecting to a Stereo Component Digital Audio Output (optical) DIGITAL COAXIAL OPTICAL DIGITAL OUT Optical Digital Cable (Sold Separately) Connect to optical digital input jack Set the “Digital Output” to “PCM” (see page 52) in “Audio Setup”. Digital connection to audio component without Dolby Digital decoder When connecting digitally, DTS-encoded audio tracks will produce distorted sound. When playing a Linear PCM Audio encoded disc, you must use the digital connection Only use an optical Digital Cable which has been designed for use with portable DVD. After the completion ...