Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
button for the AV2 input sources. 2. By means of RF Coaxial Cable After making this connection, you must preset the station received through the satellite tuner. RF output channel of the satellite receiver should be adjusted away from channel 36, which is used by the DVD-VCR, e.g. re-adjust to channel 39. 1. AV1(EURO AV): By means of 21-pin Scart Cable Plug the SCART Cable with satellite receiver or other equipment into the AV1 (EURO AV) socket on the rear of the DVD-VCR. After making this connection, select the source by pressing the INPUT SEL. button for the AV1 input sources. 2. By means of RF Coaxial Cable After making this connection, you must preset the station received through the satellite tuner. RF output channel of the satellite receiver should be adjusted away from channel 36, which is used by the DVD-VCR, e.g. re-adjust to channel 39. Satellite Receiver or other Equipment Aerial Aerial Connector RADIO ANT. AM FM 75 COAXIAL AUX IN AUDIO VIDEO DVD & VCR R L SCART Cable RF coaxial cable 12 TV Satellite Receiver or other Equipment Aerial Aerial Connector RADIO ANT. AM FM 75 COAXIAL AUX IN AUDIO VIDEO DVD & VCR R LSCART Cable RF coaxial cable 1 2 TV GB Plug & Auto Set up Your DVD-VCR will automatically set itself up when it is plugged into the mains for the first time. TV stations will be stored in memory. The process takes a few minutes. Your DVD-VCR will then be ready for use. 1 Connect the coaxial cable as indicated on page 11. (Connecting Your DVD-VCR to the TV Using the Coaxial Cable) 2 Plug the DVD-VCR into the mains. Result: The Language Set menu is displayed. 3 Select the required language by pressing the ..or .buttons. 4 Press OK to store the language selected. Result: A message appears. 5 Press OK button. 6 Press the ..or .buttons to select your country. . The VCR searches for the stations according to a preset preference list corresponding to the country that you have selected. 7 Press OK to start the auto scanning. The number of stations automatically stored by the VCR depends on the number of stations that it has found. 8 The current time and date are displayed automatically. Check the date and time. if it is : Correct, Press RETURN button twice to exit the menu. incorrect, see page 18. . Auto preset can be performed by pressing STOP ( ) on the VCR continuously for 5 seconds or more with no tape inserted. 2 RADIO ANT. AM FM 75 COAXIAL AUX IN OUT AUDIO VIDEO DVD & VCR R L TV Auto setup Please wait 00 % Time Date Year 12 : 00 1 / JAN / 2004 THU Clock Set 2 RADIO ANT. AM FM 75 COAXIAL AUX IN OUT AUDIO VIDEO DVD & VCR R L TV Auto setup Please wait 00 % Time Date Year 12 : 00 1 / JAN / 2004 THU Clock Set 13 Tuning Your Television for the DVD-VCR GB 2 4 You must tune your television for the DVD-VCR only if you are not using a Scart cable . To view pictures from your DVD-VCR when a Scart cable is used, the television must be set to the audio/video mode (AV). 1 Switch on the television. 2 Switch on the DVD-VCR by pressing STANDBY/ON on the front of the DVD-VCR or STANDBY/ON on the remote control. 3 Select a programme position on the television to be reserved for use with your DVD-VCR. 4 Insert the video cassette in the DVD-VCR. Check that the DVD-VCR starts reading the cassette; if not, press .II button. 5 Start a scan on your television or set the television to UHF channel 36. 6 Fine tune the television until the pictures and sound are obtained clearly. 7 If you cannot find the pictures and sound, or there is interference from nearby channels, it may be necessary to change the setting of the DVD-VCR output channel (see Setting the DVD-VCR Output Channel on page 23 and Problems and Solutions on page 75). 8 When the picture and sound are perfectly clear, store this channel at the desired programme position on the television. Result: That programme is now reserved for use with your DVD-VCR. 14 Deck Control Keys The DVD-VCR uses one set of controls to operate both decks. The following keys are helpful in successfully controlling each deck. STANDBY/ON Button Press the STANDBY/ON button on the remote control or front panel to turn on the DVD-VCR. DVD Button Press the DVD button on the remote control when you want to control the DVD deck. The DVD indicator will light on the Front Panel Display to show that the DVD deck is selected. VCR Button Press the VCR button on remote control when you want to control the VCR deck. The VCR indicator will light on the Front Panel Display to show that VHS deck is selected. INPUT SEL. BUTTON Press the INPUT SEL. button repeatedly to cycle through all of your input sources, including the Tuner (PR##), AV1 (rear AV input), AV2 (rear AV input), AUX (rear AV input). It is only available when VCR deck is selected. STANDBY/ON PHONES 1 1 2 3 4 GB . Before using the VCR operation of 19~45 pages, press the VCR button on the remote control to select VCR mode. Before using the DVD operation of 46~66 pages, press the DVD button on the remote control to select and watch DV...