Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
• If your TV doesn’t match any of the examples provided, see your nearest Sony dealer or qualified technician. Caution Connections between the VCR’s VHF/UHF connector and the antenna terminals of the TV receiver should be made only as shown in the following instructions. Failure to do so may result in operation that violates the regulations of the Federal Communications Commission regarding the use and operation of RF devices. Never connect the output of the VCR to an antenna or make simultaneous (parallel) antenna and VCR connections at the antenna terminals of your receiver. Getting Started 7 Getting Started SONY SLV-675HF/676HF (E) 3-856-995-11 (1) Step 3: Hookups (continued) Audio/video (A/V) hookup Page 8 If your TV has audio/video (A/V) input jacks, you will get a better picture and sound if you hook up your VCR using these connections. In addition, for a true “home theater” experience, you should connect the audio outputs of your VCR or TV to your stereo system. If your TV doesn’t have A/V inputs, see the following pages for antenna or cable hookups. If you’re not planning to use your VCR to record programs, you’re finished setting up the VCR after you’ve made the connections shown on this page. If you want to record off-air or off your cable TV system, complete these connections first, and then go to the following pages for antenna or cable hookups. A Use this hookup if your TV has stereo jacks VCR Stereo receiver Audio/video cable (supplied) AUDIO VIDEO LINE IN LINE OUT TV IN VIDEO AUDIO AUDIO OUT AUX IN B Use this hookup if your TV doesn’t have stereo jacks VCR Stereo receiver TV VIDEO AUDIO IN AUX IN AUDIO VIDEO LINE IN LINE OUT Video cable (not supplied) Audio cable (not supplied) Note To play a tape in stereo, you must use the A/V connection. Note to CATV system installer (in USA) This reminder is provided to call the CATV system installer’s attention to Article 82040 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. Getting Started SONY SLV-675HF/676HF (E) 3-856-995-11 (1) Pages 9 and 10Hookup 1 Pages 9 and 10Hookup 1 Antenna hookup Make the following connections if you’re using an antenna (if you don’t have cable TV). A Use this hookup if you’re using: • VHF/UHF antenna (you get channels 2–13 and channels 14 and higher) • UHF-only antenna (you get channels 14 and higher) • Separate VHF and UHF antennas Rear of TV VHF/UHF or or Match the type of connector on your TV: A, B, or C. A B VHF C UHF VHF VCR UHF IN OUT VHF/UHF VCR IN OUT VHF/UHF B Use this hookup if you’re using a VHF-only antenna (you get channels 2–13 only) Rear of TV VHF/UHF Match the type of A connector on your TV: A, B, or C. or VHF B For connector types B and C, no UHF UHF or connection is required. VHF C UHF If you cannot connect your antenna cable to the VCR directly If your antenna cable is a flat cable (300-ohm twin lead cable), attach an external antenna connector (not supplied) so you can connect the cable to the VHF/UHF IN connector. If you have separate cables for VHF and UHF antennas, you should use a U/V band mixer (not supplied). For details, see page 41. Getting Started 9 SONY SLV-675HF/676HF (E) 3-856-995-11 (1) Getting Started Step 3: Hookups (continued) Hookup 1: VCR setup 1 Set the RF UNIT switch to CH 3 or CH 4, whichever channel is not used in your area. If both are used, set the switch to either channel. CH3 RF UNIT CH4 For details, see page 40. If you made A/V connections (page 8), you can skip this step. 2 Press EASY SET UP on the VCR. 1 The LANGUAGE menu appears. Change the SET UP on-screen display language to Spanish LANGUAGE (ESPANOL) or French (FRANCAIS) if desired, ENGLISH ESPANOL and press EXECUTE. For details, see page 17. FRANCAIS NEXT : EXECUTE CANCEL : EASY SET UP 2 The CLOCK SET menu appears. Set the clock SET UP and press EXECUTE. For details, see page 18. CLOCK SET /1/1997 WE 12:00 AM NEXT : EXECUTE CANCEL : EASY SET UP 3 The TUNER PRESET menu appears. Set SET UP ANTENNA/CABLE to ANT and press TUNER PRESET ANTENNA / CABLE EXECUTE. For details, see page 19. • ANT CABLE SELECT : / NEXT : EXECUTE CANCEL : EASY SET UP 4 The AUTO PRESET starts. SET UP SET UP AUTO PRESET SET UP IS DONE EXECUTING / EASY SET UP 1 PLEASE WAIT . Normal display Getting Started SONY SLV-675HF/676HF (E) 3-856-995-11 (1) Pages 11 and 12Hookup 2 Pages 11 and 12Hookup 2 Cable box with many scrambled channels Recommended use Use this hookup if your cable system scrambles all or most channels. What you can do with this hookup • Record any channel by selecting the channel on the cable box What you can’t do • Record one channel while watching another channel Match the type of connector on your TV: A, B, or C. For connector types B and C, no UHF connection is required. Wall IN OUT VHF/UHF IN OUT VHF/UHF Rear of TV or or A B C VHF UHF VHF UHF Cable box VCR continued ...