Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Select either VCR or DVD mode, then continue with the other features as described in this manual. .When timer recordings are set, the TIMER light will light up, and “REC” and “ ” will appear in the front panel display. To use the DVD/VCR as usual until the time of the recording, press TIMER so that the TIMER light turns off and “REC” and “ ” disappear. Press VCR/TV to choose the VCR position. Select either VCR or DVD mode, then continue with the other features as described in this manual. If you want to use the DVD player during a timer recording or while the TIMER light, “REC” and “ ” are on or flash. .You can use the DVD player while the TIMER light, “REC” and “ ” are on or flashes, or during a timer recording. Press y/I to turn on the DVD/VCR. Press DVD on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual. You don’t have to set the . TIMER off to use the DVD only. TO STOP AN AUTOMATIC TIMER PROGRAM ALREADY STARTED Press STOP/EJECT on the DVD /VCR. TO CHECK, CORRECT, OR CANCEL AN AUTOMATIC TIMER PROGRAM 1 Press TIMER. .If the power of the DVD/VCR is off, press y/I instead of TIMER, then go on to the next step. .If the DVD output mode is selected, you have to switch it to the VCR mode by pressing the VCR on the remote control or the OUTPUT on the DVD/VCR. 2 Select main menu by pressing MENU. 3 Select "TIMER PROGRAMMING" by pressing K or L. Then, press B. 4 Select the program number you want to check by pressing K or L. .The details of the selected program appears on the TV screen. .Go to the digit you want to change by pressing B or s. Then, enter correct numbers by pressing o or p. .You may cancel the entire program by pressing s while the program number flashes. 5 Press CLEAR/C.RESET to exit. 6 Press TIMER to return to timer stand-by mode. –20– EN 1L25 SPECIAL FEATURES COPYING A VIDEO TAPE VCR You can make copies of video tapes made by friends or relatives for your enjoyment. Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. Connect the recording DVD/VCR (this unit), the playing VCR (another source) and your TV using the following diagram. .You can use the AUDIO/VIDEO input jacks on the front panel of the DVD/VCR instead of using the jacks on the back. [Recording DVD/VCR] (this unit) .Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are not recommended. .You can use a video disc player, satellite receiver, camcorder or other audio/video component with A/V outputs in place of the playing VCR. TO MONITOR THE RECORDING 1 Turn on the TV and set the TV to channel 3. .If noise appears, change the RF output channel of the DVD/VCR to channel 4 by pressing PLAY for 3 seconds during playback. Then select the same channel (CH4) on your TV. (See “RF Output Channel” on page 14 for more details). 2 Press VCR/TV on the remote control of the recording DVD/VCR. English MTS (Multi-Channel Television Sound) SYSTEM [Playing VCR] (another source) LEFT RIGHT OUT AUDIO VIDEO DIGITAL AUDIO OUT AXIAL AUDIO OUT DVD VCRDVD/VCR S-VIDEO OUT AUDIO OUT COMPONENT VIDEO OUT AUDI O IN VIDEO OUT LY CB/ PB CR/ PR R L R L R ANT-IN ANT-OUT VIDEO IN 0VM204468 Audio/Video cables(not supplied) ANT in [TV set] (Use for monitoring) RF cable (supplied) 1 Insert a pre-recorded tape into the playing VCR. 2 Insert a tape with a safety tab into the recording DVD/VCR. 3 Press SPEED on the recording DVD/VCR to select the desired recording speed (SP/SLP). 4 Select the “L1” or “L2”position on the recording DVD/VCR by pressing the CHANNEL (K/L ). .When you use the A/V input jacks on the back of the DVD/VCR, select "L1" position by pressing [0], [0], [1] or the CHANNEL(o/p) on the DVD/VCR. .When you use the A/V input jacks on the front of the DVD/VCR, select "L2" position by pressing [0], [0], [2] or the CHANNEL(o/p) on the DVD/VCR. Note “L1” and “L2” are found before the lowest memorized channel. (Example: CH2) 5 Press REC/OTR on the recording DVD/VCR. 6 Begin playback of the tape in the playing VCR. .For best results during dubbing, use the DVD/VCR’s front panel controls whenever possible. The remote control might affect the playing VCR’s operation. VCR When you play a VHS tape, or receive a broadcast on the DVD/VCR tuner channel you are watching, the current STOP 12:00AM CH 32 STEREO SAP SP 0:00:00 HIFI 1)* status will appear when you press DISPLAY on the remote control. When you record a 2)* MTS broadcast signal, you need to set it to MTS mode. 1)* Press MENU and select "TV STEREO" or "SAP" by pressing K or L. Then, press B. To exit, press CLEAR/C.RESET. .Although a program may be broadcast in both stereo and sub audio, you must select the Recording mode to TV STEREO or SAP before you record a broadcast. 2)* Press MENU and select "AUDIO OUT" by pressing K or L. Then, press B.Next, select "HIFI" or "MONO" by pressing K or L.To exit, press CLEAR/C.RESET. .While the DVD/VCR is set in HIFI stereo mode, HIFI a...