Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
6. The scan operation will overwrite any existing channel table. Highlight “Yes” and then press OK to continue. Automatic channel search will begin. • When the channel search reaches 100%, press OK. • If no channel list appears, check the ANTENNA/CABLE input jack to make sure the RF coaxial cable is properly connected. AV/INPUT DRC8335_EN(verB) 7/23/07 3:36 PM Page 14 Initial setup 13 EN 7. The channel list contains the channels you tune to when you press or on the remote control. • Press or to highlight a channel in the channel list. Press or to select an icon on the action bar at the bottom of the screen. From the channel list screen, you can hide or delete channels you rarely watch by selecting (b) “Hide/Unhide” or (c) “Remove program” icon on the action bar and then press OK. You will still be able to tune to the “hidden” channels directly by using the number buttons, but the unit will not tune to a “hidden” channel when you press CH+ or CH–. Removed channels cannot be accessed by pressing CH+ or CH– or the number buttons unless a new channel search is done. 8. Highlight the (a) “Home” icon on the action bar and then press OK to return to the main menu. a b c Searching for new channels The channel list can be updated for new channels without altering the existing list. 1. Press SETUP to access the player menus. 2. Press or to highlight “Setup”and then press OK. 3. Press or to highlight “TV Channel Setup”and then press OK. 4. Press or on the action bar at the bottom of the screen to highlight “Scan+”and then press OK. Automatic channel search will begin. 5. The channel list will now contain the new channels (if any) at the end of the existing list, follow step 7 in Searching for channels to edit the channel list. DRC8335_EN(verB) 7/23/07 3:36 PM Page 15 14 Watching TV programs Watching images from connected devices Watching TV programs In order to use the features of the unit, you will have to get used to turning on the unit to watch TV. 1. Turn on your TV set and unit. After a few seconds the main menu of the unit appears on the television screen. 2. The “Live signal” function is already highlighted. Press OK to tune to the last channel watched. • To display information on the current channel, press INFO. 3. To change channel: • On the remote control – press CH+/CH– or the number buttons to input the channel numbers (read note on the right for details). • On the unit – press SKIP CH+/SKIP CH–. Watching images from connected devices To select viewing a device connected to your unit (e.g. satellite receiver, camcorder), press INPUT on either the unit or remote control to show the action bar at the bottom of the screen. Select the input source (DV, AV1, AV2 or Tuner) by pressing or and then OK. • When viewing ATSC broadcasts, press INFO and then or to select and display the information on the current channel. • Press AGAIN/GO BACK to switch between the current and the last tuned channels when watching TV. When using the number buttons to change channel: 1. Input firstly the channel number. 2. Press . 3. Input the index number. Input “000” for analog (NTSC) channels 4. Press OK to tune to the channel. For example, to tune to channel 003-012, press “3”, , “1”, “2” and OK. If you only input the channel number and then press OK, the unit will perform channel search for all the channels start with the selected channel number (in the above example, all channels start with 003-XXX). The first channel of the selected channel number will be tuned to. DRC8335_EN(verB) 7/23/07 3:36 PM Page 16 15 EN Recording VCR recording 1. Insert a recordable tape into the tape deck. 2. If necessary, change the tape speed by pressing RECORD QUALITY on the remote control. The selected tape speed shows briefly on the TV screen. • SP = Standard play, SLP = Super long play (around x2 to x3 the recording time as the tape indicates) 3. Refer to the instructions on page 14 to watch TV and change channel, or select viewing a device connected to your unit (e.g. camcorder). 4. Press VHS REC on the unit or REC on the remote control to start recording. 5. Press PAUSE to pause recording. Press VHS REC or REC to resume. 6. Press STOP/EJECT or STOP to stop recording. Make sure the safety tab of the tape is in place. Recording is not possible if the safety tab is removed. If the safety tab is removed and you want to record, simply cover the hole with adhesive tape. Make sure the VCR is selected with the VCR indicator turned ON when using the remote control to perform the below operations. If the indicator is off, press VCR on the remote control to activate the VCR. Safety tab Press either key to start VCR recording VCR indicator Press this button DRC8335_EN(verB) 7/23/07 3:36 PM Page 17 • You will be asked to make the disc compatible when you unload the disc. If you want to play the disc on other DVD players, press OK. Otherwise, press OPEN•CLOSE to unload the disc. Copying DVD to tape 1. Make sure you see the home page of the player menus (i.e....