Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
• Lock the LCD screen in fully closed position when not in use. • Before putting on headphones, always adjust the volume setting to OFF or lowest position. • Remember to leave the dome light switch in the off or auto position when the vehicle is unattended, as the dome lights, if left on, can drain the vehicle battery. • Do not put pressure on the screen. • Caution children to avoid touching or scratching the screen, as it may become dirty or damaged. Safety Precautions For safety reasons, when changing video media, it is recommended that the vehicle is not in motion, and that you do not allow children to unfasten seat-belts to change video media or make any adjustments to the system. System adjustments can be accomplished using the remote control, while seat-belts remain fastened. Enjoy your AUDIOVOX entertainment system but remember that the safety of all passengers remains the number one priority. Licensed under one or more of the following patents, Patent Numbers 5,775,762, 5,927,784, and 6,678,892. 2 IR TRanSMIT anD RECEIVE MoDES (M1 oR M2) The AVXMTG10UA has an option that allows the user to select from two IR transmit and receive modes (M1 or M2). This feature can be used when two AVXMTG10UA units are installed in the same vehicle or if the vehicle has an RSA (Rear Seat Audio) that uses “A” channel headphones. When in the M1 mode the unit will transmit audio on the A channel. When in the M2 mode the unit will transmit audio on the B channel. If two of these units are used in one vehicle it may help to mark one remote with M1 on the back and the other remote with M2 on the back. A unit set to M2 mode will not work with a remote control programmed to the M1 mode. Conversely a unit set to M1 mode will not work with a remote control programmed to the M2 mode. To change from M1 to M2 mode, point the remote control towards the IR receiver on the AVXMTG10UA. Press and hold the M2 button for 5 to 7 seconds. The following screen will be displayed: Note: The OSD will appear on the screen for 4 – 5 seconds. To change from M2 to M1 mode, point the remote control towards the IR receiver on the AVXMTG10UA. Press and hold the M1 button for 5 to 7 seconds. The following screen will be displayed: Note: The OSD will appear on the screen for 4 – 5 seconds When the AVXMTG10UA is powered up in DVD mode it will display the following screen showing FM Modulator status and FM channel selection as well as IR Transmitter status (IR ON or IR OFF) and which mode (M1 or M2) the unit is in. 3 Materi als Included In This Package 4 1. 10” LCD Overhead Monitor with DVD player (1 pc) 2. 12 Pin Power Harness (1 pc) 3. 2 Pin Power / Wire Harness with Choke (1 pc) 4. Hardware Package M2.6 x 6mm Phillips Screws (10 pcs) M4 x 15mm Phillips Screws (4 pcs) M5 x 9mm Phillips Screws (4 pcs) M5 x 20mm Phillips Screws (4 pcs) M5 x 40mm Phillips Screws (4 pcs) CAUTION: The 20mm and 40mm screws in the hardware kit are provided to facilitate installation. Use extreme caution when using these screws to avoid damage to vehicle roof or other components, wiring, etc. 5. Remote Control (1 pc) 6. Mounting Bracket (1 pc) 7. Snap-on Shroud (2 pcs)* 8. Snap-on Screen Cover (2 pcs)* 9. Pry Tool (1 pc) 10. 3.5mm TIP/3RCA JACK PIG TAIL (1 pc) 11. Trim Ring (3 pcs) *Note: The AVXMTG10UA is supplied with a black snap-on shroud and screen cover. To install the pewter or shale snap-on shroud or screen cover, the black snap-on shroud and screen cover must be removed first. See the following page for the removal process. 1 2 3 4 5 6 7 8 9 10 11 5 REMOVING AN D Inst alli ng Snap-on Covers 1. 2. 3. 4. 10” Overhead LCD Monitor with DVD Player Shroud Screen Back Cab Pry Tool Preparation Place the unit on a soft surface to avoid damaging the plastic. Materials Required Disconnecting the Screen Cover 1 2 3 “A” “B” “C” “C” 1. Open the LCD screen. 2. Insert the supplied pry tool between the LCD screen and snap on screen cover at locations “A”, “B”, and “C” and gently pry the cover away from the screen. 6 Installing the Screen Cover “D” “D” “D” “D” Disconnecting the Shroud 1 2 “E” (fastener) 1. Open the LCD screen. 2. Hook the two tabs “D” at the bottom edge of the screen cover into the notches on the bottom edge of the LCD screen. 3. Snap the opposite side of the screen cover over the hinges.. 1. Open the LCD screen. 2. Insert the supplied pry tool between the unit and shroud at fastener location “E” and gently pry the shroud away from the unit. 7 1 2 “F” Installing the Shroud 1. Open the LCD screen. 2. Slide the shroud over the unit. The shroud will snap into place at locations “F”. GEnERaL VEhICLE InSTaLLaTIon aPPRoaCh 1. Decide upon the system configuration and options that will be installed. 2. Review all manuals to become familiar with electrical requirements and hookups. 3. Decide upon the mounting locations of all components and the method of mounting. 4. Prep the vehicle. Remove any interior trim necessary to gain access to vehicle's wiring, as well as all areas wh...