Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
The first step is to delete files not referenced by the project files and history list. The second step is to clear the history list. The history list contains a record of all previous edit operations and recording passes within the project in chronological order. This allows you to undo and redo operations, with up to 99 undo levels. Clearing the history list means you cannot undo any previous edits or recording passes. Note that any time you open a new project, the history list is automatically cleared. PROJECT PROJECT FILES MENU > New Open Save SaveAs < PROJECT FILES MENU Delete Copy Rename Purge SOURCE DRIVE: Internal << >> Next Smooth as Silk << >> Rename Cancel RENAME PROJECT AS: > OK Cancel < Smooth as Silk << >> Inc Dec 26 SDR 24/96 SDR 24/96 To purge a Project: 1. Press Project. Press the Page Right button, and in the Project Files Menu, select Purge. 2. The Purge current project? screen appears. Select OK to delete files not referenced in the project file, or Cancel to exit. 3. The PURGE: clear history? screen appears. Select Yes to clear the history list, No to leave the history list intact and retain files that are referenced in the history list, and Cancel to exit without purging. 4. Purging project... appears in the display, followed by Project purged to confirm that the project was successfully purged. Basic Transport Operations The SDR24/96 transport and recording controls are similar to those on most multitrack tape recorders. REWIND FAST FWD STOP PLAY RECORD Fast Wind REWIND and FAST FWD puts the SDR24/96 into fast wind mode from any state. Fast Wind also punches out of record and cancels master record standby. If there are unsaved recording passes, the recording passes and project file are automatically saved to disk. When pressed from stop, the “tape” rolls slowly at first, then accelerates to 20X speed in four seconds. Pressing the button a second, third, fourth, or fifth time increases the winding speed still further. ¦ 1 press: Slow wind; 20X speed after four seconds ¦ 2 presses: 60X speed ¦ 3 presses: 180X speed ¦ 4 presses: 540X speed ¦ 5 presses: 1620X speed Stop STOP brings the “tape” to an immediate halt. STOP also punches out of record and cancels master record standby. If there are unsaved recording passes, the recording passes and project file are automatically saved to disk. When the transport is already stopped, pressing STOP twice within one second moves the current locator to the beginning of the project. PROJECT PROJECT FILES MENU > New Open Save SaveAs < PROJECT FILES MENU Delete Copy Rename Purge Purge current project? OK Cancel PURGE: clear history? Yes No Cancel Scrub When the transport is already stopped, pressing and holding the STOP button for one second puts the transport into scrub mode. The STOP and PLAY LEDs light simultaneously and Entering scrub mode appears in the display. Use the REWIND and FAST FWD buttons to scrub the transport forward and backward. Press STOP or PLAY to return to normal mode. Play PLAY puts the SDR24/96 into play from any state (as if you didn’t know). PLAY also punches out of record and cancels master record standby while leaving the Transport in play. Record The master RECORD button must be pressed along with PLAY to enter record mode. The master record LED blinks if there are no tracks armed (Record Ready buttons), or not within the Autopunch zone when Autopunch is activated (see page 37). When One Button Punch is activated (SETUP:Record:Page Right:RecBt), recording can be toggled during play by pressing only the RECORD button. Serial 9-Pin The SERIAL 9-PIN connector on the rear panel of the SDR24/96 is provided for connecting transport controllers that use the EIA RS-422 serial data communication standard. It supports the Sony® 9-Pin protocol. The following transport functions can be controlled through the Serial 9-Pin connection: Stop, Play, Rec, Fast Forward, Rewind, and Scrub. Time Display Operation Guide MINUTES HOURS SECONDS FRAMES EXT CLOCK The Current Time display shows the exact position of the SDR24/96’s “playback head.” In the current version, the time format can be displayed only in SMPTE time (HH:MM:SS:Frames). Transport Menu The SDR24/96 transport menu allows you to set locate points, offsets, and enable AutoPlay. Locate Times The Locate option allow you to enter the time for Locates 1-4. To set the Locate time: 1. Press SETUP to enter the SETUP MENU. SETUP MENU > Record I/O Sync TranspSETUP 2. Select Transp. to enter the TRANSPORT OPTIONS menu. TRANSPORT OPTIONS > Loc1 Loc2 Loc3 Loc4 Operation Guide 27 28 SDR 24/96 SDR 24/96 3. Select one of the four Locates (Loc1, Loc2, Loc3, Loc4). The current locate time appears in the display. 4. Select Zero to reset the Locate point to zero. 5. Press Page Right to change the locate time. A blinking cursor appears over the first numeral of the locate time. Use the increment (Inc) and decrement (Dec) buttons to change the highlighted numeral. Use the >> button to move to the next num...
Эта инструкция также подходит к моделям:DVD-проигрыватели - SDR24 (2.38 mb)