Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
S-VIDEO OUT JACK 2. AUDIO OUT L,R JACK 3. DIGITAL AUDIO OUT JACK (OPTICAL) 4. DIGITAL AUDIO OUT JACK (COAXIAL) 5. COMPONENT VIDEO OUT JACK 6. AUDIO OUT R,L JACK 7. VIDEO OUT JACK 8. VIDEO IN JACK 9. AUDIO IN R,L JACK 10. RF OUT TO TV JACK 11. RF ANTENNA INPUT JACK 6 9 11 English - 17 Connections 16 - English Connections Accessories Step 1: Unpacking Check for the supplied accessories below. • Video/Audio Cable • RF Cable for TV • Remote Control • Batteries for Remote Control (AA Size) • User’s Manual • Dispose of used batteries according to local environmental regulations. Do not put them in the household trash. Step 2: Connecting the Antenna Cable There are several ways to connect your DVD Recorder-VCR. Select one of the following antenna connections that best suits you below. • Method 1 : Antenna + DVD Recorder-VCR + TV : No Cable box • Method 2 : Antenna +Cable box + DVD Recorder-VCR + TV : Cable box with many scrambled channels • Method 3 : Antenna + DVD Recorder-VCR + Cable box + TV : Cable box with a few scrambled channels If you are using an off-air antenna that has 300- ohm twin flat leads, use an external antenna connector (300-75 ohm adaptor : not supplied) to connect the antenna to the DVD Recorder-VCR. If you have two separate antennas (one VHF and one UHF), use a UHF/VHF combiner-adaptor (available at most electronics shops) to connect the antenna to the DVD Recorder-VCR. Note Method1 : Antenna + DVD Recorder- VCR + TV : No Cable box You can record non-scrambled channels by selecting the channel on the DVD Recorder-VCR. Also use this Method if you watch channels without cable box. Method 2 : Antenna +Cable box + DVD Recorder-VCR + TV : Cable box with many scrambled channels You can record channels by selecting the channel on the cable box. You cannot record one channel while watching another channel. Be sure that the cable box is turned on. Connecting & Setting Up Quick Overview A Quick overview presented in this guide will give you enough information to start using the recorder. Step 1 : Unpacking Step 2 : Connecting the Antenna Cable Step 3 : Connecting the Video Cable Step 4 : Connecting the Audio Cable Step 5 : Connecting External Devices Step 6 : Connecting the Power Cord Step 7 : Preparing the Remote Control . . . . . . • Quick Overview . . . . . . . . . . . . . . . . . . . 16 • Unpacking . . . . . . . . . . . . . . . . . . . . . . . 17 • Connecting the Antenna Cable . . . . . . . . 17 • Connecting the Video Cable . . . . . . . . . . 18 • Connecting the Audio Cable . . . . . . . . . . 20 • Connecting External Devices . . . . . . . . . 22 • Connecting the Power Cord . . . . . . . . . . 23 • Preparing the Remote Control . . . . . . . . . 23 • Note to CATV system installer : This reminder is pro-video to call CATV system installer’s attention to Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. English - 19 Connections 18 - English Connections Method 2 : Connecting to an S-video input jack Connect an S-video cable(not supplied) between the SVIDEO OUT jack on DVD Recorder-VCR and S-VIDEO IN jack on the TV (or AV amplifier). • You will enjoy high quality images. S-Video separates the picture element into black and white (Y) and color (C) signals to present clearer images than regular video input mode. Method 3 : Connecting to Component video input jacks(Y,CB/TB,CR/PB) in 480i mode 1. Connect Component video cables(not supplied) between the COMPONENT VIDEO OUT jacks on DVD Recorder- VCR and COMPONENT VIDEO IN jacks on the TV (or AV amplifier). 2. Make sure that the disc has stopped completely before changing the mode. If anything is not displayed on front panel display, it is 480i Mode. • You will enjoy high quality accurate color reproduction. Component video separates the picture element into black and white (Y), blue (Pb) and red (Pr) signals to present most clear and clean images. Make sure that the color coded connections match. The Y, Pb and Pr component output jacks of your DVD Recorder-VCR must be connected to the exact corresponding component input jacks on your TV. Otherwise, red or blue images will be displayed on the TV screen. Make sure that the left and right audio output jacks of your DVD Recorder-VCR are connected to the left and right audio input jacks of your TV, respectively.(page 20) Note Method 3 : Antenna + DVD Recorder-VCR + Cable box +TV : Cable box with a few scrambled channels You can record non-scrambled channels by selecting the channel on the cable box. You cannot record scrambled channels that require a cable box. Method 1 : Connecting to a video input jack Connect a video(yellow) cable between the VIDEO (yellow) OUT jack on DVD Recorder-VCR and VIDEO(yellow) IN jack on the TV(or AV amplifier). • You will enjoy...