Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
The DVD-ROM drive is the default source drive. The internal hard disk drive was formatted and partitioned at the factory. Each partition occupies 9GB of hard disk space. Partitions are arranged in numerical order starting with partition 00000, and initially contain no data. A set of data loaded into a partition on the hard disk drive is called an “image file.” To use the hard disk drive as the source drive, you must first load an image file from a DVD into a partition on the hard disk drive, select the partition that contains the data you want to copy, then execute the copy function. 1. Insert a source DVD into the DVD-ROM drive. This disc contains the data that you wish to copy to the partition on the internal hard disk drive. 2. Press the SET button to select the Load function, then press the RUN button to execute the function. The data will be loaded into the default first partition (00000). After a few moments, the source disc will be ejected, signaling the completion of the data load procedure. 3. Remove the source disc from the DVD-ROM drive. Note: If you need to load additional data from various sources, change to another partition first (e.g., 00001) using the Partition Name function in Setup mode, then repeat steps 1 and 2 above. 4. Once the data has been copied to the hard disk drive, insert a blank disc into as many of the target drives as you desire. 5. Using the SET button, change to the Copy function, then press RUN to copy from the hard disk drive to the discs. The discs will be ejected when the copying process is complete. 6. Remove the copied discs from the Duplicator. You can repeat this procedure from Step 4 if desired. TEAC 1x10 DVD Duplicator User’s Manual TEAC 1x10 DVD Duplicator User’s Manual Chapter 3. DVD Duplicator Functions The DVD Duplicator features three (3) modes of operation: . Operation mode . Setup mode . Advanced mode Operation Mode Functions Operation mode includes seven (7) functions. Each function is explained below. Test The Test function simulates writing to the target disc. The discs will remain blank after the test is complete. This function is recommended if you are using unsupported media. This function enables the target drive to adjust the laser to the proper intensity. The source drive, which is determined by the setting on the Duplicator controller, can be either the DVD-ROM drive or the hard disk drive. Copy The Copy function enables you to copy data from the source DVD or a partition on the internal hard disk drive. For more information, refer to “Basic Operation” on page 8. Compare The Compare function compares data on the source and target discs after the copy process is complete. Copy and Compare The Compare function follows immediately as soon as the Copy function is completed. Verify The Verify function verifies that the target disc was written completely and with no errors. TEAC 1x10 DVD Duplicator User’s Manual Erase Erase The Erase function erases the data from /RW media. The default setting performs a Quick Erase when you press the RUN button. You can also press and hold the RUN button for three (3) seconds to perform a Full Erase. The Full Erase requires more time than the Quick Erase. Load The factory-installed hard disk drive was partitioned and formatted at the factory. Each partition is approximately 9GB in size. The Load function enables you to transfer data from the DVD-ROM or DVD Writer drive to the current partition on the hard disk drive. If you are loading various sources to the hard disk drive, change the Partition Name to specify a new partition after the Load function is completed. This will prevent you from overwriting data that has already been loaded into the previous partition. TEAC 1x10 DVD Duplicator User’s Manual Setup Mode Functions Setup Mode Functions The Setup mode includes nine (9) functions. To enter the Setup mode, press and hold the SET button until you hear a beep. The LCD will then display SETUP. Press the SET button to scroll through the available functions. To exit the Setup mode, press and hold the SET button until you hear a beep. Each function is explained below. Automatic This function is for factory use only. Partition Name The Partition Name function enables you to setup the ID and partition number of the hard disk drive. The first two (2) digits are the ID number of the hard disk drive. This ID can range from 00 to 99. The remaining three (3) digits represent the position of the partition. The default setting is 00000. Set as Default This function allows you to set any changes or modification you have made as your default settings. Update Firmware The Update Firmware function updates the firmware on the interface board via a CD or DVD disc. The DVD Duplicator will locate the data and update its firmware automatically. During the update, do not turn off the power to the unit. Once the update is complete, the LCD will display a message and all arguments will return to the default setting. Please restart the syst...
Эта инструкция также подходит к моделям:DVD-проигрыватели - DVW-D110H (886.4 kb)