Оценок - , средний балл:
(
)
)
Производитель: Toshiba
Размер: 290.71 kb
Название файла: SD-R5372DVDRecordableUserGuide.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Read Write DVD-R 12X 16X* Capable DVD+R 12X 16X DVD-RW 6X 6X* Capable DVD+RW 6X 8X* Capable DVD+R DL 8X 5X DVD-ROM 16X n/a DVD-RAM 2X n/a CD-ROM 48X n/a CD-R 48X 48X CD-RW 24X 4X CD-DA 40X n/a HS CD-RW -10X US CD-RW -24X * Free firmware upgrade available on Toshiba SDD Website that will boost DVD-R write speed from 12X to 16X, DVD+RW write speed from 4X to 8X and DVD-RW from 4X to 6X.. 3-way Disc Eject (eject button, software, emergency eject hole) Average Random Access Time CD 100ms DVD-RAM 200ms DVD-ROM 120ms Horizontal or Vertical Mount 2MByte Buffer Playback interchangeability for CD-ROM and DVD-ROM discs Regionalization (RPC2 compliance) (DVD) BUS Interface - ATAPI Types of Disc Formats Supported - Write DVD: DVD-R, DVD-RW, DVD+R, DVD-R DL, DVD+RW CD: CD-R, CD-RW, High Speed CD-RW, Ultra Speed CD-RW Types of Disc Formats Supported - Read DVD: DVD-ROM, DVD-R/RW, DVD+R, DVD+R DL, DVD+RW, DVD-RAM CD: CD-DA, CD+G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video-CD), Multi-session (Photo-CD, CD-EXTRA, CD-R, CD-RW, Portfolio) Front Panel Figure 1.SD-R5372 DVD Writeable Drive Front Panel Load disc using tray. Loading Tray Busy Light The LED lights green or amber when the drive is operating (LED is amber when drive is LED writing.) Eject The Eject button is used to open the disc tray so you can install or remove a disc. Button Emergency The emergency eject hole is to be used only when the Loading Tray will not open when Eject Hole Eject button is pressed. System Requirements The DVD Writeable kit requires the following (If kit uses Nero6 software): • Microsoft Windows 98SE, XP, 2000 or ME • CPU Requirements: 300MHz minimum 800MHz for capturing to hard disc 1.6GHz for capturing to DVD video • 64MB RAM, 128MB RAM (for video editing) • Hard Drive Space: 500MB minimum 4.8GB for DVD Images • Screen solution 800 x 600 pixel minimum, 16 bit color depth or higher • Windows Internet Explorer 4.0 or higher • PCI sound card, USB audio box or motherboard built-in audio device • TV tuner or video capture board for analog recording SETUP – SD-R5372 The following steps must be performed to properly install your drive: • Set Drive Jumper Settings • Connect Audio Cable • Attach IDE BUS Cable • Attach Power Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pins located on the rear of the DVD Rewriteable drive. By placing a jumper on the pins, you can select the following functions: CS Drive is configured using host interface signal CSEL SL Configures drive as Slave MA Configures drive as Master (default mode) Figure 1.Mode Select Jumper In most installations, jumper should remain in the MA position (factory default). It is recommended that you install your DVD Rewriteable drive only on the secondary IDE BUS. If you are installing on primary IDE BUS, your hard drive would then be the Master, and you should set your DVD Rewriteable drive to the Slave position (SL) Figure 2.Jumper Locations Placing DVD Rewriteable Drive inside your Computer Now that you have set the jumpers, you are ready to install your DVD Rewriteable drive inside your computer. Important Note: Disconnect power from your computer system before beginning installation. Remove computer cover and faceplate if required. Refer to your computer systems manual for removal information. If the DVD Rewriteable drive is replacing a CD-ROM or DVD-ROM, remove drive presently installed in your system. Your Toshiba DVD Rewriteable drive can be placed in any free half-height drive slot at the front of your computer. (It can be mounted horizontally or vertically.) Carefully start sliding the DVD Rewriteable drive into the opening with the disc tray facing the front of the computer. Before you push the drive all the way in you will need to connect the IDE BUS cable, Audio cable and the Power cable on the back of the drive. Connecting Cables IDE BUS Cable (not supplied with drive) -Your computer system should have a primary and secondary IDE BUS, cable with your Hard Drive most likely being the Master on the primary BUS. Connect BUS cable as follows, assuring that pin 1 of cable (side with red stripe) is connected to pin 1 of the DVD Rewriteable drive's interface connector: If you are replacing your CD-ROM or DVD: Figure 3.Installing BUS Cable connect DVD Rewriteable drive to the BUS Cable connector that the CD-ROM or DVD was connected to. If DVD Rewriteable drive is not replacing a CDROM/ DVD or is an addition to a CD-ROM/DVD: connect DVD Rewriteable drive to an open connector on the secondary IDE BUS cable (not supplied with drive). If DVD Rewriteable drive is to be slave on Primary BUS: connect DVD Rewriteable drive to open connector on the primary IDE BUS cable (not supplied with drive). Power Cable - Connect an internal computer power supply cable to the power socket at the back of the DVD Rewriteable drive. One side of the plug has chamfered edges, so the power connector fits only one way. Push plug complet...