Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
1.3) DVD+R DL DVD+R (8.5GB basic Format spec Ver. 1.0) DVD+RW DVD+RW (4.7GB basic Format spec Ver. 1.2) CD-R/RW CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM XA, MIXED MODE CD, CD-I, CD-I HS CD-RW Bridge (Photo-CD, Video-CD), Multi-session CD (Photo-CD, CD-EXTRA, Portfolio) US CD-RW Types of Disc Formats Supported - Read DVD: DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18) DVD-R (Ver 1.0 for Authoring, Ver. 2.0 & Ver. 2.1 for General) DVD-RW (Ver 1.1, 1.2) DVD+R SL (4.7GB Basic Format spec. Ver. 1.3) DVD+R DL (8.5GB Basic Format spec. Ver. 1.0) DVD+RW (Ver 1.2) CD: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, CD-I, CD-I Bridge (Photo-CD, Video-CD), Multi-session (Photo-CD, CD-EXTRA, CD-R, CD-RW, Portfolio) Front Panel Figure 1.SD-R6572M DVD Writeable Drive Front Panel Loading Load disc using tray. Tray Busy The LED lights green or amber when the drive is operating (LED is amber when drive is Indicator writing.) Eject The Eject button is used to open the disc tray so you can install or remove a disc. Button Emergency The emergency eject hole is to be used only when the Loading Tray will not open when Eject Hole Eject button is pressed. SETUP – SD-R6572M Toshiba recommends that only trained professionals install this DVD Rewriteable drive into your laptop/notebook. Installation Notes • The SD-R6572M DVD Rewriteable drive has no jumpers that need to be set • Mounting orientation: 15° (horizontally), 15° vertically (volume control in down position), 30° (drive with volume control in up position). • When mounting drive use 4 M2-PO.4 tapping holes located on the left and right sides of drive. • When mounting drive, the tightening torque of the four screws must be even. Recommended screw tightening torque is 2N • For clearance around the front bezel, it is recommended that a clearance of more than 0.8mm should be left in all directions. Software Driver Toshiba's SD-R6572M drive does not require any unique device drivers for Windows '98/2000/XP/NT. After installing your drive and re-booting, your system should recognize your drive. Win '98/2000/XP/NT Operating Systems support all Toshiba's ATAPI drives natively. If you prefer using DOS, download the ATAPI driver from our web site. USING THE DVD REWRITEABLE DRIVE – SD-R6572M Drive Operation Inserting Media To insert media perform the following steps: 1. Figure 1.Inserting Disc 1. Open the drive's loading tray by pressing the Eject Button and pulling out the tray. 2. Place media disc into drive's loading tray, and lightly press down on the inner portion of the disc. 3. Gently close the disc tray. Removing Media To remove media disc from the drive, perform the following steps: 1. Open the loading tray by pressing the Eject Button, and pulling tray out. 2. Grasp disc by it's outer edge, and lift out of loading tray. 3. Gently close the loading tray. Usage Guidelines • Keep the disc tray closed when not using the DVD Rewriteable drive • Do not press down on the disc tray when opening or closing it. • Do not place objects on the disc tray • Never use a damaged, broken, or deformed disc • Do not press the Eject button while the drive is accessing a disc Emergency Ejection CAUTION: The following procedure is intended only as a last resort when pressing the eject button fails to open the Loading Tray. 1. Turn computer power OFF by properly shutting down system. 2. Insert a solid bar (i.e. large paper clip) into Emergency Eject hole and push in as shown in the picture below. 3. Loading tray will open/eject. Figure 2.Using Emergency Eject Handling Media CD/DVD media is sensitive to dust and fingerprints. Carefully handle media by its edges only. Cleaning Media Try to avoid touching the read area (underside) of the disc as dirt and smears will degrade the disc accessing speed. If the disc becomes dirty wipe it with a damp soft cloth. Avoid cleaning in a circular motion, but rather from the inner side outward. NOTE: High-speed drives spin the disc at a high rotational speed. If a disc has printing on only half of the disc, or if there is a slight imbalance in the disc, the imbalance is greatly magnified by the high speed, causing the drive to vibrate or produce a fan-like noise. These effects are inherent in the high-speed technology and do not indicate a problem with the drive. TROUBLESHOOTING – SD-R6572M Problem Solution Disc tray cannot be opened • • Check that there is power to drive. Use Emergency Eject instructions to open tray. Drive is not recognized by system • • • Is the drive connected properly? Are all cables plugged in properly (e.g. Power Cable, Interface Cable and Audio Cables). Is the software driver loaded? On a step-by-step (F8) Boot of the system is the DVD Rewriteable drive recognized? (BIOS / DOS reports "device driver not found" or "no valid drivers selected."). If not, Contact Technical Support. Has the DVD Rewriteable drive software driver been corrupted by a virus. Run a Virus Scan program and repair if possible. Contact Technical Support if the Virus renders...