|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
¦ Digital output setting is equally applied to NOTE both Dolby Digital and MPEG-2 audio. LPCM sound track is always outputted as PCM. It has no relation with Digital Output setting. ¦ Be sure to select the correct Digital Output or you will hear no sound or loud noise. DTS 1. Off : Doesn’t output DTS signal. Select this when your AV receiver or AV amplifier does not have DTS decoder. 2. On : Outputs DTS Bitstream via digital output when you play DTS track. Select this only when your AV receiver (or AV amplifier) have DTS decoder. ¦ When DTS soundtrack is played, sound NOTE does not output from AV Audio Output. AudioDVD-Recorder No Disc Programme Digital Output : PCM vv Setup DTS : Off vv Dynamic Compression : On vv NICAM : On vv OKMOVE EXIT Dynamic Compression This is only active when a Dolby Digital signal is detected. 1. Off : You can enjoy the movie with the standard Dynamic Range. 2. On : When Movie soundtracks are played at low volume or from smaller speakers, the system can apply appropriate compression to make low-level content more intelligible and prevent dramatic passages from getting too loud. NICAM NICAM programmes are divided into 3 types. NICAM Stereo, NICAM Mono and Bilingual (transmission in another language). NICAM programmes are always accompanied by a standard mono sound broadcast and you can select the desired sound by setting NICAM on or off. 1. On : NICAM mode 2. Off : Only set at this position to record the standard mono sound during a NICAM broadcast if the stereo sound is distorted due to inferior reception conditions. System Setup English -33 Setting up Video Output Options deo Output Options You can enjoy high quality image through RGB or Component video connections. 1 1 With the DVD Recorder in Stop mode/No Disc mode, press the MENU button. ProgrammeDVD-Recorder Scheduled Record List vv No Disc Programme Setup OKMOVE EXIT 2 2 Press the …† buttons to select Setup, then press the OK or v button. SetupDVD-Recorder No Disc Programme Setup System vv Clock Set vv Language vv Audio vv Video vv Parental Control vv Install vv OKMOVE EXIT 3 3 Press the …† buttons to select Video, then press the OK or v button. Video setup menu will be displayed. 4 4 Press the …† buttons to select Video Output, then press the OK or v button. Component Select this when the DVD Recorder is connected to a TV with Component jack. RGB Select this when the DVD Recorder is connected to your TV using SCART cable. VideoDVD-Recorder No Disc Programme Setup TV Aspect : 16:9 W de vv 3D Noise Reduction: Off vv Video Output : RGB DivX(R) Registration Component RGB OKMOVE EXIT 5 5 Press the …† buttons to select the desired item, then press the OK or v button. In Component mode, you can set video output to Progressive(P.SCAN) or Interlace, see page 35. Available video output jacks are as follow. Available Video Output Jack Setting mode Component mode RGB ModeOutput jack P.SCAN off mode (Interlace mode) P.SCAN on mode Component Output (Y, PB, PR) O O (TV in progressive mode) X AV1 Scart R, G, B X X O Composite O X X Composite Video out O X O S-Video out O X O System Setup VideoDVD-Recorder No Disc Programme Setup TV Aspect : 16:9 W de vv 3D Noise Reduction: Off vv Video Output : Component vv DivX(R) Registration vv OKMOVE EXIT 34- English Setting up the Progressive scan Setting up the Progressive scan If the TV supports Progressive Scan, press the P.SCAN button on the front of the DVD Recorder to enjoy. 1 1 With the DVD Recorder in Stop mode, press the P.SCAN button on the front of the DVD Recorder. The message “Press [Yes] to confirm Progressive scan mode. Otherwise press [No]” will appear. NoYes Press [Yes] to confirm Progressive scan mode. Otherwise press [No] 2 2 Press the oe v buttons to select Yes, and then press the OK button. 3 3 Set your TV to Progressive input (using the TV remote control.) ¦ Do not press the P.SCAN button if you NOTE are using a TV that does not support Progressive mode. Nothing will be displayed on the screen if pressed. ¦ Progressive setting is only available when the Video Out is set to Component. ¦ If the P.SCAN button on the DVD recorder’s front panel is pressed during playback, the prohibition mark( ) appears on the screen. ¦ Progressive setting is only available when the DVD recorder is in stop mode. Canceling the Progressive scan 1 1 With the DVD Recorder in Stop mode, press the P.SCAN button on the front of the DVD Recorder. The message “Press [Yes] to confirm Interlace scan mode. Otherwise press [No]” will appear. NoYes Press [Yes] to confirm Interlace scan mode. Otherwise press [No] 2 2 Press the oe v buttons to select Yes, and then press the OK button. 3 3 Set your TV to Interlace input (using the TV remote control.) ¦ If you press the P.SCAN button by NOTE mistake when your TV does not support Progressive mode, you need to release the Progressive mode. To release the Progressive mode, press the P.SCAN button on the front panel 2 times. The screen will recover after the PS LED on the ...
Эта инструкция также подходит к моделям:DVD-проигрыватели - DVD-R131 (4.4 mb)