Оценок - 0, средний балл: 4
(
)
)
|
Фрагмент инструкции
Point the remote control directly at the player's IR sensor. Remove any obstacles between the remote and the IR sensor. UNIT NOT WORKING Turn off the power, and then turn it on again. If you have any questions, please consult the troubleshooting guide below. If you cannot solve the problem, please contact our customer support department at 480-922-0896 or via e-mail at “customersupport@sonicblue.com”. Troubleshooting Other "BAD DISC" DISPLAYED Ensure the disc is not warped, damaged or deformed. Ensure the disc is not badly stained or damaged. Ensure the disc format is compatible with the player. NO PICTURE OR SOUND Ensure the power switch is on. Ensure the power outlet is operational. Ensure the power cord is not damaged. Ensure the power plug is connected firmly to the outlet. NO SOUND FROM HEADPHONES Ensure the headphones are in working order. Ensure the headphones volume is not set at Min. Ensure the headphones are firmly connected to the headphones jack. "NO DISC" DISPLAYED Ensure you have put the disc on the tray. Ensure the disc is not upside down. Ensure the disc is not distorted, stained or scratched. Ensure the audio jacks are securely connected. Ensure the audio connector is not damaged. Ensure the volume is turned up in VOL/CH setup. Ensure you have set the player's AUDIO settings correctly. Ensure you have selected the correct AV input for your TV Ensure the audio is not set to mute. PICTURE BUT NO SOUND POOR PICTURE OR SOUND Ensure you have set the player's AUDIO settings correctly. Ensure the disc is not scratched or stained. Ensure the AV connector or the output terminal is not damaged. SOUND BUT NO PICTURE Ensure the video jacks are securely connected Ensure you have selected the correct AV input for your TV. Ensure the video connector is not damaged. Ensure you have set the player's VIDEO settings correctly. REMOTE NOT WORKING Ensure the remote batteries are working. Point the remote control directly at the player's IR sensor. Remove any obstacles between the remote and the IR sensor. UNIT NOT WORKING Turn off the power, and then turn it on again. -34 Specifications Power requirements: ~110-240V 50/60Hz Power consumption: 25W Video standard: NTSC Weight: 7 Lbs (3.2kg) Dimensions: 17in(W) x 12.9in(D) x 3in(H) (product),(430mm(W) x 328mm(D) x 75mm(H)) Video out Video out: 1.0V(p-p)/75¦.,sync, negative polarity, RCA pin Jack x 1 S-video output connector(separate Y..C signal output connector): Y output: 1.0V(p-p)/ 75¦.,sync, negative polarity C output: 0.286 V(p-p)/75¦. 4 pin mini DIN x 1 Audio out Analog out: 1.85V(rms)/10k¦., RCA pin Jack(L,R) x 1 Coaxial out: 0.5V(p-p)/75¦., RCA pin Jack x 1 Optical out: Optical Fiber Transmitter Frequency response: 20Hz to 20kHz S/N ratio: >90dB Total harmonic distortion: < 0.05% [Accessories] Audio/Video cord 1 Remote Control 1 Batteries(AAA) 2 Specifications are subject to change without notice. Weight and dimensions are approximate. -35 ON/OFF PHONES OPEN/CLOSE PLAY REV FWD PAUSE PREV NEXT STOP .n Point the remote control directly at the player's remote sensor. .n Do not leave the remote control in an extremely hot or humid place. .n Do not spill water or put anything wet on the remote control. .n Battery life is ~1 year under normal conditions. Improper use of batteries may cause battery leakage and corrosion. To operate the remote control correctly, follow the instructions below: .n Do not insert the batteries in the wrong direction. .n Do not charge, heat, open, or short-circuit the batteries. .n Do not throw batteries into a fire. .n Do not leave dead batteries in the Remote Control. .n Do not use different types of batteries together, or mix old and new batteries. .n If you do not use the remote control for a long period of time, remove the batteries to avoid possible damage from battery corrosion. .n If the remote control does not function correctly or the operating range becomes reduced, replace all batteries with new ones. .n If battery leakage occurs, clean the battery compartment, then insert new ones. Point the remote control at the remote sensor. Distance: About 15ft from the front of the remote sensor. Angle: About 30 degrees in either direction relative to the remote sensor. Remarks: Do not expose the remote sensor of the DVD Player to a strong light source, such as direct sunlight. 2. Insert batteries. 1. Open the cover. 3. Close the cover. Make sure to match the "+" and "-" of the batteries with the marks inside the battery compartment. Insert batteries Using the remote control Notes: Notes: 1 2 3 Remote Control Preparation o 30 o 30 Items -36- (The pictures below are for reference only.) Warning / / STAND BY/ON TITLE MENU OPEN/CLOSE OSD/SETUP SLOW FWD PREV/REV NEXT/FWD PAUSE/STEP STOP PLAY MODE A-B MEMORY ENHANCE EQUALIZER VOL/CH ZOOM ANGLE SUBTITLE AUDIO PLAY RETURN ENTER CLEAR SEARCH 1 2 5 7 8 9 12 13 15 18 20 22 24 26 27 4 3 6 10 11 14 17 19 21 25 23 29 28 16 To prevent children from watching programs which have a rating above their a...