Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
< Some amplifiers may regard this signal as DVD-Audio. < DSD signal is output during playback of a SACD disc, and linear PCM digital signal during playback of a DVD-Audio disc. i.OFF Select this when you don’t use the i.LINK (AUDIO) terminal. No signal is output from the i.LINK (AUDIO) terminal. < There is no difference between i.60958 and i.PCM as far as SACD or DVD-Audio disc playback is concerned. < Set the Analog Out setting to “Multi channel” to output the surround sound from a DVD-Audio and SACD disc. When the Analog Out setting is set to “2ch”, the multichannel sound is downmixed to 2 channels. < In case you experience any problem with the audio output, read the instructions of the connected component to check the adaptable format. If the connected component cannot accept 4% down signal, set the 4% down mode off. Flow Status While the display shows “i.60958” or “i.PCM”, repeatedly press the STOP button to turn ON or OFF the flow status. If the component connected via the i.LINK terminal is compatible with the flow rate control, and if you set the flow status of the UX-3 ON, the connected component will work in the flow rate control mode. < Though the flow status function of the UX-3 is not same as the flow rate control, RAM buffer of the connected component will absorb clock differences and control the flow rate using the clock of the connected component. < In the following cases, set the flow status OFF: • The connected component isn’t compatible with the flow rate control. • Though the connected component is compatible with the flow rate control, the flow rate control doesn’t work properly with this unit. • Sound skips. < During playback of a video source, the flow status is automatically set to OFF to keep the synchronization of audio and video. < When the flow status is set to ON, “i.60958 FL” or “i.PCM FLOW” will appear on the display instead of “i.60958” or “i.PCM”. i.LINK (IEEE 1394) i.LINK (IEEE 1394) The i.LINK is also known as IEEE 1394, an international specification. This unit is ready for i.LINK (AUDIO). By connecting an i.LINK (AUDIO)-capable device to the IEEE 1394 (or i.LINK (AUDIO) terminal on this unit using an i.LINK cable, you can transmit SACD multi-channel signals that could not be transmitted but in analog format in the past can be transmitted in its original digital format, in addition to the capability of transmitting 2-ch linear PCM data and multi-channel compressed audio signals. If you have multiple i.LINK-capable devices, you can connect them through other devices to transmit data between them, so you don’t need to be concerned with the order of connection. Copyright protection system DTCP To play back audio sounds recorded on SACD or DVD discs using i.LINK, both the player and the D/A converter need to be ready for the copyright protection system DTCP (Digital Transmission Content Protection). This unit is ready for DTCP. Data transfer rate There are three transfer rates: 100 Mbps (S100), 200 Mbps (S200), and 400 Mbps (S400). This unit is capable of transferring data at a maximum 400Mbps. For connection to an i.LINK-capable device, use a commercially available S400-compliant 6-pin i.LINK cable. When connecting multiple i.LINK-capable devices, avoid connecting a device having slow transfer rate between devices having high transfer rate since this reduces the transfer rate of your whole system. Connect devices having high transfer rate towards the source as far upriver as possible. NOTES < Among the i.LINK formats there are “MPEG-2 TS” for BS digital source and “DV” for digital video for DVD recorders, as well as the “i.LINK (AUDIO)” (A&M Protocol). Never connect devices that are not ready for i.LINK (AUDIO) to this unit. If you do, this unit and others may get out of order or be damaged. < In the process of data transfer, avoid plugging/unplugging the i.LINK cables in use or switch on/off the power. < Among the i.LINK-capable devices there are some that, if not turned on, are not capable of relaying data. < Chances are some i.LINK-capable devices will not respond to this unit's command. How to connect multiple i.LINK-capable devices Daisy chain connection You can daisy-chain up to 17 devices including this unit. i.LINK cable i.LINK-capable i.LINK-capable i.LINK-capable device device device i.LINK-capable device Connection in tree structure If you are using a device having three or more i.LINK connectors, you may want to get the connection branched out. This way of connection allows you to connect up to 17 devices including this unit. i.LINK-capable device i.LINK-capable device i.LINK-capable device i.LINK-capable device i.LINK-capable device Your system does not work if data is fed back to the output device. Be careful not to create a loop. i.LINK-capable device i.LINK-capable device i.LINK-capable device i.LINK-capable device i.LINK-capable device i.LINK-capable device The i.LINK interface of this unit is designed in accordance with the following specifications: 1) IEEE ...