Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
(Please also screw the shower and tube out of the mixing valve and take note not let the hot water scald yourself. ) And then, drain the water in the tank out. Before the next usage, in order to avoid accidents, it is advised open the hot water valve first before turn on the power supply to let the gas out of the tube. It is not allowed smoking or fire near the open valve. Meanwhile, please make sure that all parts of the water heater are in good condition. 1. 2. 3. Operation Diagram 4. 5.Provided hot water quantity can meet use demand, temperature setting shall be possibly low. It can minimize heat dissipation, high-temperature corrosion and sedimentation, ensuring a longer service life. Regularly ask servicemen to make safety inspection, remove sediment on heating elements, and check consumption of anode bar. Too much consumed anode bar shall be replaced. 6. On/Off button Power on Power off Mode (Function) button Power button-Select heating power (850W / 1300W / 2150W) Real-time Heat / Warm Press Set button Press Set button Press Set button Press Set button Press Set button Clock hour setting Clock hour setting Clock minute setting Clock minute setting Medium Warm Night Power Time 1 Time 2 Time 1 hour setting Time 2 hour setting Time 1 minute setting Time 2 minute setting Press or Press or Press or Press or Calibrate Time 1 hour digits Calibrate Time 2 hour digits Calibrate Time 1 minute digits Calibrate Time 2 minute digits Time 1+Time 2 Repeat steps for Time 1 and Time 2 Intelligent Set highest heat temperature D E C F G Safety Precautions A...OAOUI.O. .».EOO A...OAOUI.O. .».EOO For first use after installation, the tank must be full of water before connecting the power. Otherwise, heating element overheat may cause troubles.Children taking shower must be attended by adults. Please do not point the showerhead towards human body when turning on or off the faucet, avoiding to be scalded by a small stream of hot water. Haier C In winter in cold regions, for long-term out-ofuse, please lift the safety valve handle to empty the water, avoiding ice formation damaging the water heater. Damaged power cord must be replaced by after-service technicians with special cable (factory provided). Other persons shall not dismantle or repair. In addition, do not place flammable matters nearby the water heater. Do not use damaged wire, socket or appliances with loose plug, otherwise accidents like electric shock, short circuit and fire may occur. Make sure power plug closely fits with power socket. .....».. Power socket for water heater shall be located in a dry place free of water spray. Do not insert or pull the power plug with wet hands, for accidents like electric shock or injury may happen. Temperature value indicated on the display is for water around the detection point. Outlet water temperature is generally higher. Before use, please first turn on cold water and then adjust water temperature as you need. During use, the displayed value is still water temperature at detection point instead of outlet temperature. Please do not directly turn on hot water. The product adopts Haier Safe Care patented technology. In normal installation, even in severe case that ground wire is live due to wrong connection, the product Safe Care technology can filter and efficiently ensure your safety. However, whenever your feel a sensory current, please pull out the power plug and notify local after-service men in time. Do not dismantle by yourself. Check if power meter and wire size are consistent with water heater rated current. If necessary, ask experienced qualified electricians to check. The water heater shall use 230 V~ / 50 Hz power supply from a separate socket (no multi-purpose socket) and be reliably grounded. Power plug pins shall be cleaned in time to avoid any contamination causing accidents like fire. Operation Instructions 9. Delay Time Setting Delay function means that, system automatically calculates the time needed to reach temperature setting value with a defaulted 2150 W power, then determines the time to start heating, and automatically heats to the set temperature before the preset delayed time to use hot water. Two Delay Times (Time 1 + Time 2) means machine as needed can heat water in two delayed use times. This machine can be manually set two delayed water use times. Setting will ta...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - SILVER SEA-OX FCD-JTHMG100- E (532.53 kb)
Дрели и шуропопверты - SILVER SEA-OX FCD-JTHMG50- E (532.53 kb)
Дрели и шуропопверты - SILVER SEA-OX FCD-JTHMG100- E (532.53 kb)
Дрели и шуропопверты - SILVER SEA-OX FCD-JTHMG60- E (532.53 kb)