Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Before using this product, please read the following instructions carefully. Technical Specifications Item Description Item Description Square Drive 1/2" Air Inlet Diameter 1/4"- 18NPT Free Speed 145 RPM Min. Hose Size 3/8" Max. Torque 65 ft-lbs Max. air pressure 90 PSI Air Consumption 4.5 CFM SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep this manual and invoice in a safe and dry place for future reference. WARNINGS AND SAFETY RULES 1.Wear proper clothing. Always use ANSI-approved safety impact goggles when assembling or using this tool. Wear long sleeved shirts, long pants and hard-toed shoes. Take off any loose fitting jewelry and keep long hair covered to prevent being caught in moving parts. 2.Keep work area clean and well lighted. A dim and/or cluttered work area invites personal injury. 3.Keep children and pets away from work areas. Children can be a distraction and should be supervised by an adult when near the work area. Never allow children to play with this product even if it is turned off. 4.Store idle tools properly. Keep this tool out of the reach of children. 5.Do not use the wrench if under the influence of alcohol or prescription drugs, or if you are tired. Doing so may cause damage to the tool, or personal injury. Do not use this or any tool if you are tired. Use common sense at all times. 6.Always use the proper tools. This tool was designed for a specific task. Do not alter this tool, or use it for a purpose for which it was not intended. 7.Be careful when connecting/disconnecting air supply. It is recommended to use quick disconnects (not included) rather than screw-on air connections. 8.Use compressed air only. Clean, dry, regulated compressed air at 90 PSI. Never use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool. 9.Always disconnect air supply when this tool is not being used. NOTE: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be under stood by the operator that common sense and caution are factors that cannot be built into this product but must be supplied by the operator. 1 of 4 NOTE: READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT ASSEMBLY You Air Ratchet Wrench comes completely assembled. For information on parts, please refer to parts list & diagram on this manual. Air Connection 1.Remove the plastic cap from the rear of the motor housing. The cap is attached to the connection head. 2.You will need a union fitting (not included) before you can connect your Air Ratchet Wrench to an air compressor. Attach the Union fitting to the motor housing. Tighten the fitting. 3.Attach an Air coupler (not included) to the union fitting it desired. This is a useful accessory as it allows quick-coupling action when using a variety of tools with the drops of Pneumatic Tool Oil to the airline connection. Add a few drops more after hour of continual use. OPERATION 1.Select the desired socket. Attach the socket to the Ratchet Anvil. 2.Set the compressor's pressure regulator to 90 PSI. Do not set the compressor's outlet regulator to over 90 PSI. Connect the compressor hose to the Air Ratchet wrench at the air inlet at the back of the tool. If any leaking is detected, disconnect the air hose and have it repaired prior to use. 3.You can check the direction of the drive by pressing the Reverse Button (#39). To change the direction of the drive, turn towards R for reverse and F for forward. (Tighten or Loosen). 4.Place the socket over the nut to tighten or loosen. Grip the air ratchet firmly. Press the trigger to turn the nut. When tightening a nut, begin by threading the nut on as far as you can by hand. 5.When the nut is in place, tightened or removed, stop the Air Ratchet wrench by releasing the trigger. Remove the nut from the socket if needed. Turn off the compressor then remove the Air Ratchet wrench connection from the compressor. 6.When tightening: check the recommended torque specification for the nut. You should use a torque wrench to torque the nut after using the Air Ratchet Wrench. ! WARNING If the air ratchet wrench can not loosen a nut, or if it stalls when tightening the nut, do not raise the outlet pressure of the air compressor. Do not continue attempts to loosen with the air ratchet wrench. Use appropriate tools and methods to loosen the nut. Fig. 1 same air compressor. Your Air Ratchet Wrench is now ready for use. SET UP NOTE: If you are not using an automatic oiler system, before operation, add a few 2 of 4 MAINTENANCE Your Air Ratchet Wrench is best operated with an airline oiler. If you are using this tool without an airline oiler, follow steps below: 1.Disconnect the Air Ratchet from the air hose. 2.Apply a few drops of Pneumatic Tool Oil through the air line before each use, or...