Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
DO NOT ATTEMPT to rewire the motor. Your KAWASAKI™ Drill Press is virtually maintenance free. The drill press should be cleaned after every usage preventing unwanted debris from interfering new work pieces. On a regular basis, perform the following: 1. Use an air hose and blow any dust that may accumulate in the motor. This is very important if you use the drill press on metal work pieces. 2. Brush all dust and debris away from the worktable. 3. Apply a coat of furniture-type paste wax to the worktable surface and the column. This will allow the components to function better and lessen the chance of rust forming on the metal parts. LUBRICATION The ball bearings in the motor are packed in grease at the factory and should require no further lubrication. 1. Apply a thin coating of lithium grease on the table rack. The aerosol type will work fine. This keeps the rack and the table-crank gears from binding. Periodically, remove the grease with a solvent, such as acetone, and re-apply it. 2. Apply a thin coating of lithium grease to the surfaces of the spindle and arbor. 31 Noisy operation 1. Incorrect belt tension 2. Dry spindle 3. Loose spindle pulley 4. Loose motor pulley 1. Adjust Tension. See Section Installing the Drive Belts. 2. Lubricate Spindle 3. Check retaining nut on center pulley. Tighten if necessary. 4. Check setscrews on motor pulley. Tighten if necessary. Drill bit burns 1. Incorrect speed 2. Chips not coming out of hole 3. Drill bit dull 4. Feeding too slow 5. Not lubricated 1. Change speed 2. Retract drill bit frequently to clear chips 3. Change drill bits 4. Increase feeding 5. Lubricate drill bit Drill bit leads - holes not round 1. Hard grain in wood 2. Defective drill bit 1. Replace drill bit Wood splinters on underside 1. No “back-up” material under workpiece 1. Clamp workpiece under workpiece Workpiece is torn from hands 1.Workpiece not supported or clamped properly 1. Clamp workpiece to work table Drill bit binds in workpiece 1.Workpiece pinching drill bit 2. Excessive feed pressure 3. Improper belt tension 1. Clamp workpiece 2. Slow feeding speed 3. Adjust Tension. See Section Installing the Drive Belts. Excessive drill bit run-out or wobble 1. Bent drill bit 2.Worn spindle bearings 3. Drill bit not properly locked in drill chuck 4. Drill chuck not properly installed 1. Replace drill bit 2. Contact Alltrade Customer Service 3. Re-set drill bit 4. Reinstall drill chuck. See Installing the Drill Chuck Quill returns too slow or too fast 1. Improper spring tension 1. Adjust return spring Drill chuck fails to remain on arbor spindle. 1. Dirt, grease, or oil on inside surface of drill chuck mounting hole or on outside surface of arbor spindle 1. Clean drill chuck and arbor spindle. See Installing the Drill Chuck. SPECIFICATIONS SPECIFICATIONS Voltage 120V 60 Hz Rated Current 6.6 A No-Load Speed (motor) 1725 RPM Max. Distance From Spindle Axis To Surface Of Column: 6 5/8" (170.275mm) Max. Distance From Spindle End To Surface Of Table: 30 3/4" (781.050mm) Spindle Travel: 3 1/8" (79.375mm) Chuck Capacity 5/8" (15.875mm) Range of Spindle Speeds 210-3840 RPM Laser Beam Class II, Diode Laser Average Radiant Power 1mw Laser Beam Wavelength 650nm OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would like further information on the following products, please contact Alltrade Customer Service Department at 1-800-590-3723. Cordless Drills/Screwdrivers Impact Wrenches Sanders Jigsaws Circular Saws Angle Grinders Reciprocating Saws Routers Rotary Tools Corded and Cordless Multi-Purpose Tools Wide Range of Accessories and more 34 TROUBLESHOOTING To avoid any accidental starting of the Drill Press, turn the switch to the “OFF” position, remove the safety key, and unplug the tool from the AC power source. Should the motor fail to run, for any reason, call Alltrade Customer Service. ACCESSORIES Optional accessories for the drill press can include wire-brush wheels that can be used for cleaning and layered cloth wheels that can be used for polishing and buffing. Contact ALLTRADE Customer Service at 1-800-590-3723 (toll free) to find out what accessories are available for the drill press. Only use accessories that are designed to fit your particular drill press. These accessories should be specifically labeled to match the speed and arbor size of the grinder. Failure to use the proper accessories could result in property damage, damage to the grinder, and serious personal injury to the operator. Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets. If the drill press must be used outside, use an extension cord labeled “W-A” or “W.” These extension cords are rated for outdoor use and reduce the chances of electrical shock. If you must use an extension cord, be sure that the gauge is large enough to carry the amount of current necessary for your power tool. If not, your tool may experience a loss of power, excessive...