Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
2. Start drilling with slow speed andfully charged in six (6) to ten (10) for driving screws. High gear provides Always be alert NICKEL-CADMIUM BATTERY gradually increase speed as drill cuts. Strike long arm of wrench sharply and brace yourself • If equipped with a hours. faster speeds for drilling lighter work. !CAUTIONThe harder the material, the slower counterclockwise, remove wrench and against the twisting action of the drill. nickel-cadmium To change speeds, slide switch to the the speed required. The softer thebattery, the battery unthread chuck from spindle. CHARGING 6. If drill stalls or becomes jammed in high or low position. Actuate trigger material, the faster the speed. must be recycled or Connect the current carrying prongs slightly if the gear shift does not fully INSTALLING CHUCK the hole, release trigger 3. When drilling a large hole, it is easier on the power cord to a 230V / 240V AC engage. immediately, remove drill bit from disposed of in an To install chuck, reverse “Removing to first drill a smaller hole and then 50Hz wall outlet. Connect the other work and determine cause of environmentally Note: If Drill/Driver is running, but the Chuck” procedure. Always keep the enlarge it to the required size. sound manner. Check with your end of the power cord to the battery stalling or jamming. chuck will not turn, check to make sure spindle threads, chuck threads, and NOTICE 4. The use of a lubricant, such as oil, county’s Public Works Department pack. If the charger is equipped with Do not squeeze the gear shifting switch is pushed fully securing screw free of debris. on the drill point helps keep the bit batteries. as the battery pack is connected to the GENERAL DRILLING an attempt to free a stalled or jammed cool, increases drilling action and charger and the charger is plugged in. ADJUSTABLE CLUTCH !WARNINGdrill. This will damage the motor. prolongs drill bit life. for information on recycling an LED, a red light will light up as long trigger on and off in into desired setting. The front end of 5. If possible, punch the drilling be fully charged after about three (3) settings. Output torque will increase as be made “live” if the tool drills into reversed to help free a jammed bit. position first to prevent drill bit run Charging Battery With normal use, the battery pack will This Drill/Driver features 16 clutch the Drill/Driver may The direction of rotation may be REMOVING BATTERY PACK to six (6) hours. Disconnect charger the clutch ring is rotated from 1 to 16. live wiring in the wall. TO PREVENT Be sure direction of rotation is away. Before charging, remove battery pack from power source when not in use. 1 to 2 for driving small screws. ACCIDENTAL ELECTRICAL SHOCK, HOLD RESET before attempting to DRIVING WOOD SCREWS from Drill/Driver by depressing the IMPORTANT: THE BATTERY PACK DRILL/DRIVER ONLY BY THE SOFT GRIP continue drilling. 3 to 4 for driving screws into soft battery release button and pulling the 1. Drill pilot and shank clearance SHOULD NOT BE LEFT ON THE HANDLE. materials or plastics. 7. Reduce the pressure on the drill just holes. See chart titled “Suggested battery pack out of tool. CHARGER FOR MORE THAN before the bit cuts through the Hole Sizes for Wood Screws.” 5 to 7 for driving screws into FORTY-EIGHT (48) HOURS. work to avoid splintering wood or GENERAL INSTRUCTIONS softwoods. 2. Install proper screwdriver bit. With normal use, as battery pack stalling in metal. 8 to 10 for medium woods. approaches the discharged state, you 3. Set torque adjusting collar for 8. When bit has completely Operation 11 to 14 for driving screws into 1. Set torque adjusting collar for penetrated work and is spinning desired torque and set speed performance. When the tool is unable will notice a sharp drop in tool medium / hard woods. selector to “1,” the low-speed VARIABLE-SPEED TRIGGER drilling operation and set speed freely, withdraw it from the work setting. then turn off drill. 4. Set drill for correct rotation. selector to appropriate speed. while the motor is still running, to perform the task at hand, it is time SWITCH (some models) 15 to 16 for driving screws into metal. to recharge the battery pack. If your Drill/Driver is equipped with The “drill” position locks up the clutch 2. Be sure drill bit is securely gripped Recharging the battery pack before a variable-speed trigger switch, the to permit heavy-duty drilling and in chuck. DRILLING WOOD 5. Start screw straight in hole with this condition is reached will reduce pressure you apply to the trigger driving work. It also allows bits to be 3. Set FORWARD/REVERSE BUTTON for fingers. In addition to the instructions listed Charger and Battery controls the tool speed. Apply more changed quickly and easily in the clockwise rotation. 6. Place bit on screw, start drill and under GENERAL DRlLLlNG, the pressure to increase the speed and keyless chuck. exert pressure to drive screw. Make sure work is following also apply: release pressure to d...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - DX151905CD (202.95 kb)