Оценок - , средний балл:
(
)
)
Производитель: Central Pneumatic Air Compressor
Размер: 209.45 kb
Название файла: 2439.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq. ) Warning! Operation of equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. Unpacking When unpacking, check to make sure the parts listed on page 6 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible Operation 1/4” - 18 NPT Angle Drill For best service you should incorporate an oiler, regulator, and inline filter, as shown in the diagram above. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. 1. You will need to prepare a 1/4” air connector (sold separately) to connect to the Air Inlet (12) on the Angle Drill. First, wrap the 1/4” air connector (not included) with pipe thread seal tape before connecting to a 3/8” ID Air Source Hose (not included). Connect the Air Source Hose to the Angle Drill. Note: If you are not using an automatic oiler system, before operation, add a few drops of Pnuematic Tool Oil to the airline connection. Add a few drops more after each hour of continual use. 2. Set the air pressure on your compressor to 90 PSI. Do not exceed the maximum air pressure of 90 PSI. 3. Check the air connection for leaks. Operation Note: This drill can be used to get into hard to reach places with it’s angular configuration. It may also be used just like a traditional drill. This drill does not have a reverse drive. Warning! Always disconnect the unit from the air compressor when changing bits. Warning! After drilling or driving screws, the bit will be extremely hot. Do not touch it until it has had ample time to cool down. 1. Insert the Chuck Key (44) into one of the holes in the Collet (41) and turn it counterclockwise to open the jaws. 2. Insert the bit and hand tighten it, then tighten it with the Chuck Key (44) by turning it clockwise. 3. With heavy leather gloves on, tug on the bit and make sure it is securely attached. Check that it is straight. Note: Always use sharp bits. Dull or damaged bits may cause undue stress on the drill and possibly break causing injury. Bits are available at Harbor Freight Tools. 4. Securely clamp your workpiece. Drilling 5. When drilling wood, place the bit at the point to be drilled. If you are drilling a hard, smooth surface, use a punch to mark the drill location. Grasp the drill firmly with both hands and slowly squeeze the Trigger (3). Never force the tool. Only apply light pressure when horizontal drilling. Note: For fine tune air adjustment, slowly turn the Nut (9) until you achieve the desired air flow. Note: When drilling plastics or plastic coated chip board, follow the same directions as stated in number 5 for wood. Note: If a bit becomes wedged into the workpiece, remove it from the drill and use the appropriate hand tools to remove it. 6. When drilling metal, always use a punch to mark the drilling position. Use a lubricant with most metals, to prolong the life of the bit and increase the drilling action . With steel, tin, and sheet metal use a light machine oil, with aluminum, use paraffin. Do not use lubricants with brass, copper, and cast iron. Grasp the drill firmly with both hands and slowly squeeze the Trigger (3). Never force the tool. Only apply light pressure when horizontal drilling. 7. When driving screws, use bits suitable for the type and size of screw you are using. Drill a pilot hole for the screw head to bite into. Use the lowest torque setting. Grasp the drill firmly with both hands and slowly squeeze the Trigger (3). Never force the tool. To back out a screw, use the appropriate hand tools. . Maintenance Disconnect the drill from the air compressor while perfoming maintenance. 1. Clean the unit with a damp cloth. Never use solvents to clean the unit. 2. Inspect the chuck and remove any dirt or debris. 3. Periodically oil the hinge on the Trigger (3). 4. Use a grease gun (not included) to add grease to lubricate the Bevel Gear (30) and Bevel Gear (34) through the Grease Cap (43). Parts List Part No. Description Qty. Part No. Description Qty. 1 Housing 1 26 Gear 1 2 Valve Bushing 1 27 Pin 2 3 Trigger 1 28 Hex Nut 1 4 Pin 1 29 Bushing 1 5 O-Ring 1 30 Bevel Gear 1 6 Valve Stem 2 31 Angle Head 1 7 Spring 1 32 Bearing 1 8 O-Ring 2 33 Work Spindle 1 9 Nut 1 34 Bevel Gear 1 10 Muffler Cover 1 35 Screw 1 11 Retaining Ring 1 36 Bearing 1 12 Air Inlet 1 37 Bushing 1 13 Bearing 1 38 Washer 1 14 End Plate 1 39 C-Ring 1 15 Rotor 1 40 Washer 1 16 Rotor Blade 4 41 Collet 1 17 Pin 2 42 Collet Screw 1 18 Cylinder 1 43 Grease Cap 1 19 Front Plate 1 44 Chuck Key 1 20 Bearing 2 21 Steel Ball 1 22 Washer 1 23 Gear Ring 1 24 Bearing 2 25 Gear Seat 1 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS ...