Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
DO NOT CONTINUE using product with its batteries in a depleted condition. 6. To prolong battery life, avoid leaving on charge for extended periods of time (over 30 days without use). Although overcharging is not a safety concern, it can significantly reduce overall battery life. 7. The batteries will reach optimum performance after being cycled 5 times during normal usage. There is no need to run the batteries down completely before recharging. Normal usage is the best method of discharging and recharging the batteries. Safety Warnings and Instructions: Drilling 1. Hold tool firmly to control its twisting action. WARNING: Tool may stall (if overloaded or improperly used) causing a twist. Always expect the stall. Grip the drill firmly to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting. Operating Instructions Inserting an Accessory • Hold the screwdriver upright as shown in Figure 2 and pull down on the chuck sleeve . • Insert a hex shank accessory into the holder. • Release the sleeve. NOTE: If bit does not fit into spindle, rotate the bit and re-insert it. Do not insert a bit tip without a bit tip holder. Removing an Accessory • Hold the screwdriver upright as shown in Figure 2 and pull down on the chuck sleeve . • Pull accessory straight out. Switch To turn the tool ON in a forward direction, press the top section of the rocker switch and the tool will run. Release pressure from the switch and the tool will stop. To operate in reverse, press the bottom section of the rocker switch. Without depressing the rocker switch the tool is locked and will act as any conventional, non-powered screwdriver. Angling the screwdriver To convert the tool to an angled screwdriver, push in on the release button shown in Figure 3 and rotate the top portion of the tool until it locks into one of the remaining two positions. Three Position Screwdriver Warnings: • To avoid being pinched, hold the screwdriver as shown in Figure 3 when changing positions. • Do not use screwdriver as a pry bar in any position. • To avoid screwdriver being turned on accidentally, do not carry in your pocket. Torque Control To set the tool’s torque, rotate the adjustable torque collar as shown in Figure 4. There are 12 clutch settings in all. These are indicated by screw icons depicted on the torque collar. For light duty work when using small screws, set the collar to one of the smaller screw icon settings. Each click in a clockwise direction means an increase in the torque produced. The highest position is depicted by a drill bit icon which should be used when drilling with the screwdriver. If you do not know the appropriate setting to use when tightening a screw, begin at the lowest torque setting. If the clutch ratchets before the desired result is achieved, increase the collar setting and continue tightening the screw. Repeat until you reach the correct setting. Two Speed Operation The dual range feature of your screwdriver allows you to shift gears for greater versatility. To select low speed, (high torque setting), turn tool off and permit to stop. Push the slide switch located on the top of the tool to the left. Use low speed for screwdriving operations. To select the high speed, (low torque setting), turn tool off and permit to stop. Slide gear shifter fully to the right. Use high speed for drilling operations. LED Light To turn the light on, push the slide switch located on the underside of the screwdriver toward the front of the tool. Drilling • Use sharp drill bits only. • Support and secure work properly, as instructed in the safety Instructions. • Use appropriate and required safety equipment, as instructed in the safety instructions. • Secure and maintain work area, as instructed in the safety instructions. • Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it. • Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit. • Hold the tool firmly with two hands to control its twisting action. • DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT. • Minimize stalling on breakthrough by reducing pressure and slowly drilling through last part of hole. • Keep the motor running while pulling the bit out of a drilled hole This will help reduce jamming. • Make sure switch turns drill on and off. WARNING: It is important to support work properly and to hold the drill firmly to prevent loss of control which could cause personal injury If you have questions on how to operate tool, call: 1-800-544-6986. Drilling in Wood Holes in wood can be made with the same twist drill bits used for metal. These bits should be sharp and should be pulled out frequently when drilling to cle...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - PD600G (1.01 mb)