Войти:
Оценок - , средний балл: ( )

Инструкция по эксплуатации Black & Decker, модель 1575-10

Производитель: Black & Decker
Размер: 2.62 mb
Название файла: 09a07cf0-517f-453f-8ce5-ca9b2118e126.pdf

Язык инструкции:en

Документ загружается, подождите пожалуйста
Документ загружается, подождите пожалуйста

Фрагмент инструкции


Keep handles dry, clean, and free from oil and grease. 14. DISCONNECT TOOLS. When not in use, before servicing, and when changing accessories, such as blades, bits, cutters. 15. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 16. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is off when plugging in. 17. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so ma rked. 18. STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are tired. 19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have switches replaced by authorized service center. Do not use tool if switch does not turn it on a nd off. 20. DO NOT OPERATE portable electric tools near flammable liquids or in gaseous or explosive atmospheres. Motors in these tools normally spark, and the sparks might ignite fumes. « HOLE SAW MANDRELS For and Drills to fit %" to 1^4" Hole Saws No. 40093 Mandrel with Pilot Drill to fit I1/*” to I1/*" Hole Saws No. 40094 Mandrel with Pilot Drill to fit above Mandrels No. 22192 High Speed Steel Pilot Drill Only HIGH-SPEED HOLE SAWS Use with Mandrels (Former Nos. in parentheses) Saw Outside Diam. Cat. No. For Vi" or %" Drills For For fl| Conduit Pipe Tap y Sizes Sizes 36468 %" Hole Saw has built-in Mandrel; no separate Mandrel supplied. %" 21747 40093 (22181) %" 21748 40093 (22181) W m *" 21749 40093 (22181) vs iw 21771 40093 (22181) IVn' 22809 40093 (22181) Lrfff mk 1%" 21772 40093 (22181) vs HbH W if,/' 21773 40093 (22181) 1" W I / 1 y4” 21781 ' 400&4 (22182) l%" 21782 40094 (22182) v> l!/2" 21783 40094 (22182) 1VS Also available; No. 14935 Pilot drill; fits former Mandrels Nos. 14903» 14904 and and 18028. No. 22192 Pilot drill; fits former Mandrels Nos. 22181 and 22182. Carbon Removing Brushes Made of tempered-steel wire; Used with Va" drills to . B remove rust and scale from metals. Leaves a burnished surface. A. No. 21416 Heavy-duty solid wire-filled brush. B. No. 21417 Side-flare brush for close corner work. C. No. 21419 Hoi low-core, flare-bottom brush. No. 21418 Small cleaning brush. (Not shown.) - -gat -a* 3" Wire Cup Brush Use in cleaning and removing rust scale, old paint. No. 39014 (straight chuck shank). Max. safe RPM—5,000. <±, Heavy-Duty Tool Box Cat. No. 50078 13"x8*/2"x 3/4" Drill Stop Capacity W' to y2". Governs drilling depth. No. C 1578 Drill Stop. ft (ED Wire Wheel Brushes Use in cleaning and removing rust, scale, old paint. No. 39008 4" Fine Brush, crimped; Max. safe RPM—4,500 No. 39009 4" Coarse Brush, crimped; Max. safe RPM—4,500 0 H*= Wheel Arbors Fit *4" to Vzn Drills. Carry grinding wheels, wire wheel brushes and buffing wheels. No. 39026 y4" Arbor (Vfc"dia., *4" shank). No. 8449 V2" Arbor (l/2" dia., ¥2" shank). Buffing Wheels Use with V4" to V2" Drills and Wheel Arbors. No. 39015 3" x %" x ¥2" Cotton Buff. Rubber Backing Pad Fit to ¥2" Drills. No. 66547 4%" Rubber Backing Pad with plain shank. Cat. No. Bit Diam. (in.) Usable Drilling Depth (In.) Shank Diam. (in.) Round-Shank Masonry Bits These bits are carbide-tipped for 55702 3/u W2 1# top performance and extra-long 55703 lA ‘ ' 2 ¥4 life in most masonry-drilling 55704 I# ' 2% Va applications. 55705 % 2% Va 55706 '¥2 ‘ ■ 2% ¥4 56932 4*/« v; 7 SCRUDRILL® OPERATION DRILLING — Turn the knurled collar until the “square” next to the,word “DRILL" is lined up opposite the indicator on the gear case (Fig. 1). This position is for normal drilling. SCREWDRIVING— Turn the knurled collar until the “square” next to the word “SCREW” is lined up opposite the indicator on the gear case (Fig. 1), This position is for normal screwdriving or screw removal. DRIVING SCREWS Available bits are Cat. No. 18593 Bit Assembly for No. 12 slotted head screws. Cat. No. 46098 Bit and Finder for No. 5 to No. 9 slotted head screws, Cat. No. 49278 Magnetic Dri11-Screw Chuck for driving self-d rilling, self-tapping screws with a y4” hex head and Cat. No. 63957 Magnetic Bit Tip Holder for holding bit tips with y4” hex shanks. Adjust the collar to the screw driving position then insert the correct screw driving bit into chuck. Make sure that chuck jaw rests squarely on the “flats” of the bit — tighten chuck jaws securely using key in all 3 -holes in the chuck. Turn on the unit and the chuck an...

Эта инструкция также подходит к моделям:
Дрели и шуропопверты - 6023-10 (2.62 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории