Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. To determine the minimum wire size required, refer to the chart below: CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS NAMEPLATE TOTAL EXTENSION CORD LENGTH - FEET iiîlÜ-lit«; ., V 25 50 75 100 125 150 175 200 0-10.0 18 i-M: 16 1.4v 14 12 ' If. 10.1-13.0 16 16 14 14 14 12 12 12 13.1-15.0 14 14 12 12 12 12 12 _ Before using an extension cord, inspect it for loose or exposed wires, damaged insulation, and defective fittings. Make any needed repairs or replace the cord if necessary. Black & Decker has extension cords available that are U.L. listed for outdoor use. OVER CORRECT USE OF CHUCK UNPLUG DRILLS Turn collar to open chuck jaws, insert accessory shank into chuck as far as it wili go. Tighten chuck collar first by hand, and then with chuck key, using all, three holiOi.Jiltasa shank, turn chuck key counter-clockwise in just one hole, then loosen chuck by hand. SWITCH To start Drill, depress trigger switch; to stop Drill, release trigger. To lock trigger in "ON” position for continuous operation, depress trigger and push up locking button (located below the trigger), then gently release trigger. To release locking mechanism, depress trigger fully, then release it. Do not lock the switch "ON” when drilling by hand so that you can instantly release the trigger switch if the bit binds in the hole. Be sure to release the switch locking button before disconnecting the plug from the power supply. Failure to do so will cause the tool to start immediately the next time it is plugged in. Damage or injury could result. DRILLING 1. U npdug.:: --ilHi v:.. -wlten^v iit^clung®r chan|in|.ltti®racci|iinisv , /; 2. Use-sharp dri|l' lis.tilf, for WOOD, ^use-twist drill bits, spade bits, power auger bits, or hole saws. For METAL, use highspeed steel twist drill bits or hole saws. For MASONRY, such as brick, cement, cinder block, etc.,-use«r|Me€ippsci bits.' 3. Be sure the material to be drilled is anchored or clamped firmly. If drilling thin material, use a wood "back-up” block to prevent damage to material. 4. Center-punch an indentation at the point to be drilled. This will overcome tendency of bit to slip around on a smooth surface. Place the tip of bit in indentation and turn motor "ON.” 5. Always apply pressure in a straight line with the bit. Use enough pressure to keep drill biting, but do not push hard enough to stall motor or deflect bit. To minimize stalling on breaking through the material, reduce pressure on drill and ease the bit through last part of hole. 6. Hold drill firmly to control the twisting action of the drill. 7. THE DRILL STALLS if it is being overloaded or improperly used. RELEASE TRIGGER IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT CLICK TRIGGER OFF AND ON IN ATTEMPT TO START A STALLED DRILL. 8. Keep motor running when pulling bit back out of a drilled hole. This will help prevent jamming. 9. Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The cutting lubricant that works best is sulphurized cutting oil. Aluminum is best drilled with kerosene. CLEANING & LUBRICATION Use only mild soap and a damp doth to clean the tool. Other cleaners contain chemicals which could seriously damage the plastic. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. Self-lubricating bearings are used in the tool and periodic relubi ication is not required. In the unlikely event that your drill should ever require service, take or send it to your iocal Black & Decker Service Center. Service center addresses are listed on the owner's registration card packed with your tool. IMPORTANT To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by BLACK & DECKER Service Centers or other qualified service organizations, always using Black & Decker replacement parts. ACCESSORIES Recommended accessories for use with your Drill are listed below. (CAUTION: The use of any other accessories might be hazardous.) For safety in use, the following accessories should be used only in the sizes specified below: BITS, METAL DRILLING—Up to 1/4" with 1/4" DRILL, up to 3/8" with 3/8" DRILL BITS, MASONRY DRILLING—Up to 1/2". BITS, WOOD DRILLING—Up to 1/2" with 1/4" DRILL; up to 3/4" with 3/8" DRILL HOLE SAWS-Up to 1-1/8" with 1/4" DRILL; up to 1-1/2" with 3/8" DRILL WIRE BRUSHES-Up to 3" diameter. GRINDING WHEELS-Type 1 only; up to 2" diameter; up to 1/2" thick. BUFFING WHEELS-Up to 4" diameter. BACKING PADS—4-5/8" diameter. SANDING DISC & POLISHING BONNETS up to 5" diameter. Use any Black & Decker...