Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Repeat until you reach the correct setting. Use this setting for the remaining screws. During normal operation of this product, if the front clutch fails to fully engage into the drill position then please see the following procedure: 1. Turn clutch collar to Position 1. 2. Hold the drill chuck by hand. 3. Run the unit until you hear a ratcheting sound. 4. Turn clutch collar to drill position . KEYLESS CHUCK (FIGURE 6) To insert a drill bit or other accessory: 1. Grasp the rear half of the chuck with one hand and use your other hand to rotate the front half in the counterclockwise direction, as viewed from the chuck end. 2. Insert the bit or other accessory fully into the chuck, and tighten securely by holding the rear half of the chuck and rotating the front portion in the clockwise direction as viewed from the chuck end. WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur when changing accessories. SCREW DRIVING For driving fasteners, the reversing button should be pushed to the left. Use reverse (button pushed to the right) for removing fasteners. When moving from forward to reverse, or vice versa, always release the trigger switch first. ON BOARD BIT STORAGE A bit storage slot is built-in to the area just above the battery. DRILLING • Use sharp drill bits only. • Support and secure work properly, as instructed in the Safety Instructions. • Use appropriate and required safety equipment, as instructed in the Safety Instructions. • Secure and maintain work area, as instructed in the Safety Instructions. • Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it. • Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit. • Hold the drill firmly with two hands to control its twisting action. • DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT. • Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole. • Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming. • Make sure switch turns drill on and off. WARNING: It is important to support the work properly and to hold the drill firmly to prevent loss of control (figure 3) which could cause personal injury. If you have any questions on how to properly operate tool, call: 1-800-544-6986. DRILLING IN WOOD Holes in wood can be made with the same twist drill bits used for metal or with spade bits. These bits should be sharp and should be pulled out frequently when drilling to clear chips from the flutes. DRILLING IN METAL Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil. DRILLING IN MASONRY Use carbide tipped masonry bits. Refer to Drilling section. Keep even force on the drill but not so much that you crack the brittle material. A smooth, even flow of dust indicates the proper drilling rate. Maintenance Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts. Troubleshooting Problem Possible Cause Possible Solution • Unit will not start. • Battery not installed properly. • Check battery installation. • Battery not charged. • Check battery charging requirements. • Lock-off button actuated. • Move lock-off button from center position. • Battery will not charge. • Battery not inserted into charger. • Insert battery into charger until red LED appears. • Charger not plugged in. • Plug charger into a working outlet. Refer to “Important Charging Notes” for more details. • Surrounding air temperature • Move charger and tool to too hot or too cold. a surrounding air temperature of above 40 degree F(4,5°C) or below 105 degree F (+40,5°C). For assistance with your product, visit our website for the location of the service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986. The RBRC™ Seal The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been paid by Black & Decker. In some areas, it is illegal to place spent nickel-cadmium batteries in the trash or municipal solid waste stream and the RBRC program provides an environmentally conscious a...