Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Have the Power Pack checked at your local B&D Service Center. 2. If the indicator light starts blinking fast after charging has started, your Power Pack is defective. Have the Power Pack checked at your local B&D Service Center. 3. If you feel that the Power Pack does not fully charge, recharge the Power Pack. Be sure the charger indicator light is out before inserting the Power Pack into the Charger. Watch to be sure light starts to blink slowly. V.VL j 'O, r-' I j Figure 3 Groove Groove REPLACING THE POWER PACK INTO TOOL HANDLE Insert Power Pack into handle of drill; the slot groove in the Power Pack should be located toward the side of the drill that has the screws, as shown in Figure 4. If drill and Power Pack will not assemble remove Power Pack and reorient so slot groove in pack will match key in handle. NOTE: The side of the power pack with the groove is the side with the label on it. Figure 4 6 TRIGGER SWITCH & CONTROL SWITCH The Drill is turned “ON” and “OFF” by pulling and releasing the Trigger Switch. However the trigger can be locked “OFF” by positioning the Control Switch Button at the end of its slot (Figure 5). This position should be used to prevent the Trigger from being accidentally turned on, when attaching or removing the Power Pack, when attaching or changing accessories, or when cleaning the Drill. SCREW DRIVING For driving fasteners, the Control Switch Button should be in the “Forward” position (Figure 6). Use the “Middle” position (Figure 7) for removing fasteners. When moving from FORWARD to REVERSE, or vice versa, always release the trigger first. Control Switch Button Figure 5 Control Switch Button Figure 6 ('FRO N ^ \ Trigger i>Y'” Control Switch X \ Button \ \ Figure 7 CHUCK & KEY Turn Chuck Key counterclockwise to open chuck jaws. Place bit in chuck as far as it will go. Tighten chuck collar by hand. Place chuck key in each of the three holes, and tighten in clockwise direction (Figure 8). It’s important to tighten chuck with all three holes to prevent bit slippage. To release bit, turn chuck key counterclockwise in just one hole, then loosen chuck by hand. THE CHUCK ON THIS DRILL IS NONREMOVABLE. IF DAMAGED RETURN TO AN AUTHORIZED BLACK & DECKER SERVICE CENTER. When not in use, the chuck key can be stored in the end of the handle. To remove the key, pull it firmly upward out of its holding socket. To replace key, push key's handle firmly and completely down into the holding socket (Figure 9). Figure 9 Figure 10 DRILLING (Figure 10) 1. Lock Trigger Switch “OFF” with control switch when attaching or changing bits or accessories. 2. Use sharp drill bits only. For WOOD, use twist drill bits or spade bits. For METAL, use highspeed twist drill bits. For MASONRY, such as brick, cement, cinder block, etc., use carbide-tipped bits. 3. Be sure the material to be drilled is anchored or clamped firmly. If drilling thin material, use a wood “back-up" block to prevent damage to material. 4. Center-punch an indentation at the point to be drilled. This will overcome tendency of bit to slip around on a smooth surface. Place the tip of bit in indentation and turn motor “ON.” 5. Always apply pressure in a straight line with the bit. Use enough pressure to keep drill biting, but do not push hard enough to stall motor or deflect bit. To minimize stalling on breaking through the material, reduce pressure on drill and ease the bit through last part of hole. 6. Hold drill firmly to control the twisting action of the drill. DRILLING IN WOOD Holes in wood can be made with the same twist drill bits used for metal or with spade bits. These bits should be sharp and should be pulled out frequently when drilling to clear chips from the flutes. Work that is apt to splinter should be backed up with a block of wood. Let up on the pressure just before the tip cuts through, to obtain a good clean hole. DRILLING IN METAL Use a cutting lubricant when drilling ferrous metals. The exceptions are iron and brass which should be drilled dry. The cutting lubricants that work best are sulphurized cutting oil or lard oil, bacon grease will also serve the purpose. CLEANING & LUBRICATION Use only mild soap and a damp cloth to clean the tool. Many household cleaners contain chemicals which could seriously damage the plastic. Also, do not use gasoline, turpentine, lacquer or paint thinner, dry cleaning fluids or similar products. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. Self lubricating bearings are used in the tool and periodic relubrication is not required. However, it is recommended that, once a year, you take or send the tool to a B&D Service Center for a thorough cleaning, inspection and lubrication of the gear case. DRILL STORAGE 1. The best storage place is one that is cool and dry—away from direct sunlight, heating pipes and ducts, furnaces, etc. 2. Best storage temperature is approximately +75° F. Do not sto...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - 9024 (3.02 mb)