Оценок - 4, средний балл: 3.3 ( )

Производитель: Bosch Размер: 1.24 mb Название файла: Язык инструкции:

Cordless Drills/Drivers RUBBERIZED GRIP BIT AND BIT STORAGE BATTERY RELEASE TABS BATTERY PACK FORWARD/REVERSING LEVER & TRIGGER LOCK VARIABLE SPEED TRIGGER SWITCH GEAR SHIFTER ADJUSTABLE CLUTCH KEYLESS CHUCK FIG. 1 VENTILATION OPENINGS BIT STORAGE ADAPTER Model number 32609 32612 32614 32618 Voltage rating 9.6 V 12 V 14.4 V 18 V No load speed 1 n0 0-300/min n0 0-400/min n0 0-400/min n0 0-400/min No load speed 2 n0 0-1000/min n0 0-1200/min n0 0-1200/min n0 0-1300/min Maximum Capacities Chuck size 3/8" 3/8 3/8" 3/8" Screw sizes #12 x 3" #14 x 3" #16 x 3" #16 x 3" Mild metal 1/4" 3/8" 1/2" 1/2" Hard wood 3/4" 1-1/4" 1-1/2" 1-1/2" Soft wood 1-1/4" 1-1/2" 2" 2" Charger BC001-6 & BC016 BC001-6 & BC016 BC001-6 & BC016 BC004-6 & BC016 BC130 & BC230 BC130 & BC230 BC130 & BC230 BC130 & BC230 Voltage rating 120 V 60 Hz 120 V 60 Hz 120 V 60 Hz 120 V 60 Hz Battery pack BAT048 BAT043-BAT046 BAT038-BAT041 BAT025 & BAT026 BAT100-BAT119 BAT120-BAT139 BAT140-BAT159 BAT160-BAT189 BC006 charger requires 12 V DC input NOTE: ONLY USE CHARGERS LISTED ABOVE -8 BM 2610925941 6-05 6/10/05 10:21 AM Page 9 Operating Instructions VARIABLE SPEED CONTROLLED TRIGGER SWITCH Your tool is equipped with a variable speed trigger switch. The tool speed can be controlled from the minimum to the maximum nameplate RPM by the pressure you apply to the trigger. Apply more pressure to increase the speed and release pressure to decrease speed. This accurate speed control enables you to drill without center punching. It also permits you to use as a power screwdriver. Bits are available for driving screws as well as running bolts and nuts. FORWARD/REVERSING LEVER & TRIGGER LOCK Your tool is equipped with a forward/ reversing lever and trigger lock located above the trigger (Fig. 1). This lever was designed for changing rotation of the chuck, and for locking the trigger in an “OFF” position to help prevent accidental starts and accidental battery discharge. For forward rotation, (with chuck pointed away from you) move the lever to the far left. For reverse rotation move the lever to the far right. To activate trigger lock move lever to the center off position. !CAUTION Do not change direction of rotation until the tool comes to a complete stop. Shifting during rotation of the chuck can cause damage to the tool. GEAR SHIFTING Your tool is equipped with two separate gear ranges, low gear and high gear. Low gear provides high-torque and slower drilling speeds for heavy duty work or for driving screws. High gear provides faster speeds for drilling lighter work. To change speeds slide switch, to the high or low position. ATTENTION: If your tool appears to be running, but the chuck will not turn, check to make sure the gear shifting switch is pushed fully into desired setting. ADJUSTABLE CLUTCH Your tool features 15 clutch settings. Output torque will increase as the clutch ring, is rotated from 1 to 15. The drill “ ” position will lock up the clutch to permit drilling and driving heavyduty work, and also enables bits to be changed quickly and easily in the keyless chuck. BRAKE When the trigger switch is released it activates the brake to stop the chuck quickly. This is especially useful in the repetitive driving and removal of screws. BIT STORAGE ADAPTER Your tool is equipped with a bit storage adapter that will allow you to store a longer bit if desired. To install bit adapter, remove bit from standard storage area, then snap adapter into it’s place. To use, hold bit adapter in place when removing bit (Fig. 1). INSERTING BITS REMOVING CHUCK Move reverse switch lever to the center “OFF” Rotate the clutch ring to the drill bit position. Remove battery pack and rotate the symbol “ ”. Open the chuck all the way, clutch ring to the drill bit symbol remove left-hand thread screw inside chuck “ ”. Rotate the chuck sleeve counter-by turning it clockwise (Fig. 2). clockwise viewing from chuck end, and open chuck to approximate drill bit diameter. Insert a clean bit up to the drill bit flutes for small FIG. 2 CHUCK bits, or as far as it will go for large bits. Close SLEEVE chuck by rotating the chuck sleeve clockwise and securely tighten by hand. !WARNING Do not use the power of the drill while grasping chuck to loosen or tighten bit. Friction burn or hand injury is possible if attempting to Insert the short arm of a 3/8" hex key wrench grasp the spinning chuck. and close jaws on flats of wrench (Fig. 3). -9 BM 2610925941 6-05 6/10/05 10:21 AM Page 10 Strike long arm of wrench sharply counterclockwise, remove wrench and unthread chuck from spindle (Fig. 3). INSTALLING CHUCK Always keep the spindle threads, the threads of the chuck and securing screw free of debris. To install a chuck, reverse “removing the chuck” procedure. FIG. 3 RELEASING AND INSERTING BATTERY PACK Release battery pack from tool by pressing pack. To insert battery, align battery and slide on both sides of the battery release tabs and battery pack into tool until it locks into pull downwards. Before ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: