Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
If using the power tool at a higher voltage than the rated voltage, it will result in abnormally fast motor revolution and may damage the unit and the motor may burn out. 16. NEVER use a tool which is defective or operating abnormally. If the tool appears to be operating unusually, making strange noises, or otherwise appears defective, stop using it immediately and arrange for repairs by an authorized JOHN DEERE DEALER. 17. NEVER leave tool running unattended. Turn power off. Don’t leave tool until it comes to a complete stop. 18. Carefully handle power tools. Should a power tool be dropped or struck against hard materials inadvertently, it may be deformed, cracked, or damaged. 1/2-Inch and 3/8-Inch Drill Operator's Manual WARNING SPECIFIC SAFETY RULES AND SYMBOLS (CONTINUED) 19. DO NOT WIPE PLASTIC PARTS WITH SOLVENT. Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may damage and crack plastic parts. Do not wipe them with such solvents. Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry thoroughly. 20. ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI Standard Z87.1. 21. ALWAYS be careful with buried objects such as under ground wiring. Touching active wiring or electric cable with this tool, may cause an electric shock. Confirm if there are any buried objects such as electric cable within the wall, floor or ceiling where you are going to operate here after. 22. Definitions for symbols used on this tool Volts = V Hertz = Hz Amperes = A No load speed = no Watt = W Class II Construction = Revolutions per minute = ---/min CAUTION SAVE THESE INSTRUCTIONS AND MAKE THEM AVAILABLE TO OTHER USERS AND OWNERS OF THIS TOOL! DOUBLE INSULATION FOR SAFER OPERATION To ensure safer operation of this power tool, JOHN DEERE has adopted a double insulation design. “Double insulation “ means that two physically separated insulation systems have been used to insulate the electrically conductive materials connected to the power supply from the outer frame handled by the operator. Therefore, either the symbol “ ” or the words “Double insulation” appear on the power tool or on the nameplate. Although this system has no external grounding, you must still follow the normal electrical safety precautions given in this Instruction Manual, including not using the power tool in wet environments. To keep the double insulation system effective, follow these precautions: a. Only JOHN DEERE AUTHORIZED DEALER should disassemble or assemble this power tool, and only genuine JOHN DEERE replacement parts should be installed. b. Clean the exterior of the power tool only with a soft cloth moistened with soapy water, and dry thoroughly. Never use solvents, gasoline or thinners on plastic components; otherwise the plastic may dissolve. SERVICE TOOL SERVICE MUST BE PERFORMED ONLY BY A JOHN DEERE AUTHORIZED SERVICE CENTER. Service or maintenance performed by unqualified personnel could result in a risk of injury. WHEN SERVICING A TOOL, USE ONLY IDENTICAL REPLACEMENT PARTS. FOLLOW INSTRUCTIONS IN THE MAINTENANCE SECTION OF THIS MANUAL. Use of unauthorized parts or failure to follow Maintenance Instruction may create a risk of electric shock or injury. 1/2-Inch and 3/8-Inch Drill Operator's Manual Functional Description NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety instructions contained in this manual. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool. MODEL: ET-3505-J ET-3506-J NAME OF PARTS: 1/2-Inch Drill (ET-3505-J) 3/8-Inch Drill (ET-3506-J) (Fig. 1) SPECIFICATIONS: Drill ET-3505-J and ET-3506-J: Model Motor Power Source Current No-Load Speed Drill Chuck Capacity Electric Brake Capacity: Steel- Twist Bit Hole Saw Wood- Flat Spade Bit Auger Bit Self Feed Bit Hole Saw Weight (without cord) ET-3505-J ET-3506-J Single Phase, Series Commutator Motor Single Phase 120V AC 60 Hz 9.0A 0-850/min. 1/2" (13mm) Yes 1/2" (13mm) 2" (51mm) 1-1/2" (38mm) 1-1/4" (32mm) 2-1/8" (54mm) 4" (102mm) 4.6 lbs (2.1kg) 0-3000/min 3/8" (10mm) No 3/8" (10mm) — 1" (25mm) — — 1-1/8" (29mm) 4.0 lbs (1.8kg) 1/2-Inch and 3/8-Inch Drill Operator's Manual Operation APPLICATIONS: Boring holes in metal, wood and plastic. PRE-OPERATION: 1. Power source: Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate. 2. Power switch: Ensure that the switch is in the OFF position. If the plug is connected to a receptacle while the switch is in the ON position, the power tool will start operating immediately and can cause serious injury. 3. Extension cord: When the work area is far away from the power source, use an extension cord of sufficient thickness and rated capa...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - ET-3505-J (482.29 kb)