Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
If the notch in the piston rod did not engage the Retract Pin in the Ratchet Link when the Link was joined to the Housing, it will engage the Pin automatically during the first advance stroke. 4. When the Link is connected to the Housing and the wrench is started, the reaction surface of the wrench will move against the contact point and the nut will begin to turn. 5. When the nut is no longer turning and the Pump Gauge reaches the preset pressure, release the remote control button. The piston rod will retract when the button is released and under normal conditions, an audible “click” will be heard as the tool resets itself. 6. Continue to cycle the tool until it “stalls” and the preset psi/torque has been attained. 7. Once the nut stops rotating, cycle the tool one last time to achieve total torque. LUBRICATION Marine Grade Moly Lube Lubrication frequency is dependent on factors known only to the user. The amount of contaminants in the work area is one factor. Tools used in a clean room environment will obviously require less service than a tool used out-doors and dropped in loose dirt or sand. Marine Grade Moly Lube is formulated not to wash out of the tool in areas where lubrication is critical. Whenever lubrication is required, lubricate as follows: 1. Separate the Low Profile Driver Assembly from the Ratchet Link if they are joined. 2. After wiping of the old grease, apply a daub of Marine Grade Moly Lube to the hooking notch in the Piston rod and wipe a film of Moly Lube onto the sides and faces of the two Sliders. 3. Disassemble the Ratchet Link as instructed in the Maintenance Section and wash the components in a suitable cleaning solution in a well-ventilated area. 4. Dry the components, then wipe a film of Marine Grade Moly Lube onto the wear surface of both Side Plate Sleeves and the hubs of the Ratchet. 5. Spread a light film of Marine Grade Moly Lube onto the inner faces of both Side Plates covering the area where the Drive and Segment Pawl travel. DO NOT pack the teeth of the Segment Pawl or Ratchet with lube. It can prevent the teeth from engaging properly. 6. Reassemble the Ratchet Link as instructed in the Maintenance Section. Wrench Positions Dwg. 2 TIGHTEN LOOSEN SHROUD REACT BETWEEN THESE POINTS TX Series Torque Conversion Chart Bar/N.M. Hex Sizes Bar TX-2 TX-4 TX-8 TX-16 TX-32 3/4" to 1-13/16" 19 to 46MM N.m. 1-7/8" to 2-3/8" 47 to 60MM N.m. All Hex Sizes All Hex Sizes N.m. All Hex Sizes All Hex Sizes N.m. 2-5/8" to 3-15/16" 65 to 100MM N.m. 4" to 4-5/8" 105 to 115MM N.m. 2-7/16" to 4-5/8" 80 to 115MM N.m. 4-11/16" to 6-1/2" 115 to 155MM N.m. 68 260 312 365 416 469 522 285 342 399 455 512 569 535 644 752 854 962 1,071 1,125 1,357 1,590 1,822 2,055 2,288 2,115 2,535 2,955 3,382 3,802 4,229 2,250 2,700 3,150 3,600 4,051 4,501 #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! ,016 6,019 7,022 8,025 9,028 ,031 82 95 109 122 136 150 572 625 678 728 784 626 683 740 797 868 1,179 1,288 1,389 1,498 1,606 2,528 2,768 3,008 3,248 3,489 4,650 5,070 5,490 5,917 6,337 4,951 5,401 5,851 6,301 6,751 #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 11,035 12,038 13,041 14,044 ,047 163 177 190 204 218 832 885 937 990 1,045 923 981 1,038 1,097 1,159 1,715 1,823 1,925 2,033 2,142 3,762 4,034 4,307 4,579 4,853 6,764 7,185 7,605 8,032 8,452 4,826 7,651 8,101 8,551 9,015 #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 16,050 17,053 18,057 19,060 ,063 231 245 258 272 286 1,093 1,145 1,197 1,250 1,307 1,212 1,270 1,328 1,385 1,450 2,250 2,359 2,460 2,569 2,677 5,063 5,275 5,485 5,696 5,908 8,879 9,299 9,720 10,147 10,567 9,466 9,916 10,368 10,818 11,333 #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 21,066 22,069 23,072 24,075 ,079 299 313 326 340 354 1,353 1,406 1,457 1,510 1,567 1,507 1,566 1,624 1,682 1,742 2,786 2,894 2,996 3,104 3,213 6,152 6,396 6,640 6,884 7,128 10,987 11,414 11,834 12,261 12,682 11,786 12,240 12,692 13,147 13,692 #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 26,082 27,085 28,088 29,091 ,094 367 381 394 408 422 1,613 1,666 1,718 1,769 1,829 1,799 1,857 1,914 1,972 2,033 3,321 3,430 3,531 3,640 3,748 7,334 7,540 7,747 7,953 8,161 13,102 13,522 13,949 14,369 14,796 14,148 14,604 15,061 15,518 15,888 #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 31,097 32,101 33,104 34,107 ,110 435 449 462 476 490 1,873 1,926 1,979 2,029 2,090 2,089 2,146 2,204 2,262 2,325 3,857 3,965 4,067 4,175 4,284 8,386 8,611 8,837 9,062 9,289 15,217 15,637 16,064 16,484 16,911 16,342 16,796 17,250 17,630 18,314 #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 36,113 37,116 38,119 39,123 ,126 503 517 530 544 558 2,134 2,187 2,238 2,291 2,352 2,379 2,437 2,494 2,553 2,615 4,392 4,501 4,602 4,711 4,819 9,520 9,754 9,985 10,219 10,452 17,331 17,752 18,172 18,599 19,019 18,772 19,231 19,687 20,146 20,361 #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 41,129 42,132 43,135 44,138 ,141 571 585 598 612 626 2,394 2,447 2,498 2,551 2,614 2,669 2,726 2,784 2,843 2,908 4,928 5,029 5,138 5,246 5,355 10,701 10,951 11,200 11,449 11,699 19,446 19,866 20,287 20,714 21,141 20,814 21,267 2...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - 32 (316.52 kb)
Дрели и шуропопверты - 4 (316.52 kb)
Дрели и шуропопверты - 8 (316.52 kb)
Дрели и шуропопверты - TX 2 (316.52 kb)