Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
[] Inspect the tool carefully to make sure no breakage or damage occurred during shipping. [] Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool. [] If any parts are damaged or missing, please call 1-800-932-3188 for assistance. PACKING LIST 3/8 in. Drill Battery Pack Charger Double-ended Bit (2) Operator's Manual KEYLESS CHUCK The keyless chuck allows you to hand-tighten or release the drill bit in the chuck jaws. LEVELS Levels are located on the top and end of the motor housing to help keep the drill bit level during use. TORQUE ADJUSTMENT RING Your drill has a 24-position clutch. The torque adjustment ring can be turned to select the right amount of torque for your application. TWO SPEED GEAR TRAIN The two-speed gear train is designed for drilling or driving at LO (1) or HI (2) speeds. A slide switch is located on top of your drill for selecting either LO (1) or Hi (2} speed. VARIABLE SPEED The variable speed switch trigger delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure. _, WARNING: If any parts are damaged or missing do not operate this tool until the parts are replaced. Failure to do so could result in possible serious personal injury. A WARNING: Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. A WARNING: To prevent accidental starting that could cause serious personal injury, always remove the battery pack from the tool when assembling parts. A WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. A WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. A WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury. APPLICATIONS You may use this tool for the purposes listed below: [] Drilling in wood [] Drilling in ceramics, plastics, fiberglass, and laminates [] Drilling in metals [] Mixing paint CAUTION: If at any point during the charging process none of the LEDs are lit, remove the battery pack from the charger to avoid damaging the product. DO NOT insert another battery. Return the charger and battery to your nearest Sears or other qualified service center for service or replacement. LED FUNCTIONS OF CHARGER LED WILL BE ON TO INDICATE STATUS OF CHARGER AND BATTERY PACK: [] Red LED on = Fast charging mode. [] Green LED on = Fully charged and in maintenance charge mode. [] Green LED on = When battery pack is inserted into charger, indicates hot battery pack or that battery pack is out of normal temperature range. [] Yellow and Green LEDs on = Deeply discharged or defective battery pack. [] No LED on = Defective charger or battery pack. CHARGING THE BATTERY PACK The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it until the green LED on the front of the charger comes on. NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by recharging) for them to become fully charged. CHARGING A COOL BATTERY PACK If battery pack is below normal temperature range, the green LED on charger will come on. Allow battery pack to reach normal temperature, then the red LED will come on. NOTE: If the charger does not charge the battery pack under normal circumstances, return both the battery pack and charger to your nearest Sears or other qualified service center for electrical check. [] Charge the battery pack only with the charger provided. [] Make sure the power supply is normal household voltage, 120 volts, 60 Hz, AC only. [] Connect the charger to the power supply. [] Place the battery pack in the charger aligning raised rib on the battery pack with the groove in the charger. See Figure 2. [] Press down on the battery pack to be sure contacts on the battery pack engage properly with contacts in the charger. [] Normally the red LED on charger will come on. This indicates the charger is in fast charging mode. [] Red LED should remain on for approximately 1 hour then the green LED will come on. Green LED on indicates battery pack is fully charged and charger is in maintenance charge mode. NOTE: The green LED will remain on until the battery pack is removed from the charger or charger is disconnected from the power supply. [] If both yellow and green LEDs come on, this indicates a deeply discharged or defective battery pack. Allow the battery pack to remain in the charger for 15 to 30 minutes. When the battery pack re...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - 11551 (2.13 mb)