Оценок - , средний балл: ( )

Инструкция по эксплуатации Black & Decker, модель BDG1400

Производитель: Black & Decker
Размер: 200.69 kb
Название файла:

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

5. The battery should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using tool with its battery in a depleted condition. 6. To prolong battery life, avoid leaving the battery on charge for extended periods of time (over 30 days without use). Although overcharging is not a safety concern, it can significantly reduce overall life. 7. When the battery is inserted into the charger, the red “Charging Indicator” light will come on indicating that there is contact between the battery and charger. The light will stay on as long as the battery is in the charger and the charger is plugged into a working outlet. It WILL NOT flash, go out or change to a different color when the charging cycle is complete. 8. The battery will reach optimum performance after being cycled 5 times during normal usage. There is no need to run the batteries down completely before recharging. Normal usage is the best method of discharging and recharging the batteries. Operating Instructions TRIGGER SWITCH & REVERSING BUTTON - FIGURE 3 The drill is turned ON and OFF by pulling and releasing the trigger switch shown in figure 3. The farther the trigger is depressed, the higher the speed of the drill. A forward/reverse control button determines the direction of the tool and also serves as a lock off button. To select forward rotation, release the trigger switch and depress the forward/reverse control button. To select reverse, depress the forward/reverse control button the opposite direction. The center position of the control button locks the tool in the off position. When changing the position of the control button, be sure the trigger is released. TORQUE CONTROL - FIGURE 4 To set the tool’s torque, rotate the adjustable torque collar as required. There are 6 clutch settings in all. For light duty work when using small screws, set the collar to a low number on the collar. Each click in a clockwise direction means an increase in the torque produced. The highest position is the drill mode and is indicated by a drill bit icon. In this position the clutch will not operate. This permits heavy duty drilling. KEYLESS CHUCK To insert a drill bit or other accessory: 1. Grasp the rear half of the chuck with one hand and use your other hand to rotate the front half in the counterclockwise direction, as viewed from the chuck end. 2. Insert the bit or other accessory fully into the chuck, and tighten securely by holding the rear half of the chuck and rotating the front portion in the clockwise direction as viewed from the chuck end. WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur when changing accessories. SCREW DRIVING For driving fasteners, the reversing button should be pushed to the left. Use reverse (button pushed to the right) for removing fasteners. When moving from forward to reverse, or vice versa, always release the trigger switch first. ON BOARD BIT STORAGE A bit storage slot is built-in to the area just above the battery. DRILLING • Use sharp drill bits only. • Support and secure work properly, as instructed in the Safety Instructions. • Use appropriate and required safety equipment, as instructed in the Safety Instructions. • Secure and maintain work area, as instructed in the Safety Instructions. • Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it. • Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit. • Hold the drill firmly with two hands to control its twisting action. • DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT. • Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole. • Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming. • Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The lubricants that work best are sulphurised cutting oil or lard oil. • When using twist drill bits to drill holes in wood, it will be necessary to pull the bits out frequently to clear chips from the flutes. • Make sure switch turns drill on and off. WARNING: It is important to support the work properly and to hold the drill firmly to prevent loss of control which could cause personal injury. If you have any questions on how to properly operate tool, call: 1-800-54-HOW-TO (544-6986). DRILLING IN WOOD Holes in wood can be made with the same twist drill bits used for metal or with spade bits. These bits should be sharp and should be pulled out frequently when drilling to clear chips from the flutes. DRILLING IN METAL Use a cutting lubricant when drilling metals. The...