Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Do not use tool if switch does not turn it on and off. • CAUTION: When drilling or driving into walls, floors or wherever live electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by insulated grasping surfaces to prevent electric shock if you drill or drive into a live wire. SAVE THESE INSTRUCTIONS Motor Your B&D tool is powered by a B&D built motor. Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than 10% will cause loss of power and overheating. All B&D tools are factory tested; if this tool does not operate, check the power supply. Switch (Figure 1) Pulling the trigger switch turns the tool “ON”; releasing the trigger switch turns the tool “OFF". For controlling the rotational direction of the spindle, there is a lever, integral to and on top of the trigger switch. For drilling (forward position) this lever should be slanted to the left side of the tool (viewing from behind the handle); for easing drill bits out of tight holes (reverse position) it should be slanted to the right side of the tool. A built-in mechanical interlock prevents changing the direction of the tool unless the trigger switch is released. After any reversing, return lever to forward position. REVERSE 4b A. FORWARD Right Angle Drill Head CHANGING SPEEDS BY REVERSING THE RIGHT ANGLE HEAD Your right angle drill comes from the factory with the right angle f installed in the low speed (400 RPM) position. The speed of the tool ca increased to 900 RPM by removing and reversing the right angle hea described below. TURN OFF AND UNPLUG THE DRILL. 1. Remove the chuck by opening the Jaws and inserting the hex wrt supplied into the socket screw inside the chuck. Turn the s( counterclockwise to remove it from the spindle. Pull the chuck str; off of the drill. (Do not attempt to unscrew the chuck.) 2. Loosen the forward clamping screw on the right angle head clami shown in Figure 2, using the hex wrench provided. NOTE: It ma necessary to loosen both clamp screws. 3. Pull the head straight off of the drill. (Take care not to lose the adt inside the clamp.) 4. Turn the right angle head around and align notches in the adapter witl drive pins in the right angle head. 5. Re-assemble the right angle head onto the drill and tighten the cl screws. IMPORTANT: TIGHTEN BOTH CLAMP SCREWS ALTERNA' AT LEAST 4 TIMES EACH TO A TORQUE OF APPROXIMATELY 10< LBS. TO ASSURE PROPER CLAMPING FORCE. 6. Place chuck on spindle of right angle head and align drive pins in sp with grooves on chuck. Insert the chuck screw and tighten seci (clockwise) with the hex wrench provided. 2 ADAPTER CLAMP HEAD Figure 2 CHUCK PAP SCREW Use Of Tool As A Standard End Handle Drill TURN OFF AND UNPLUG DRILL. The right angle head can be removed to convert the drill to a standard end handle drill with a spindle speed of 600 RPM. Simply remove the right angle head, clamp and adapter as instructed above and install the chuck directly onto the tool spindle. NOTE: When using the tool without the right angle head, remove and save the adapter from the spindle. Do not Install chuck with adapter in place. Side Handles TURN OFF AND UNPLUG DRILL. Whether or not you are using the right angle head the tool will need a side handle for operator control. NEVER ATTEMPT TO USE THIS TOOL WITHOUT A SIDE HANDLE FIRMLY ATTACHED. Attaching Side Handle to Right Angle Head: Select, from the carton, the side handle shown in Figure 3A. Screw it into the hole in the right angle head as shown in the figure. Tighten securely. (It can be installed on either side of the tool.) Attaching Side Handle to Gear Case: When the right angle head is not used, the side handle must be attached to the gear case (Figure 3B). Because of the extremely high torque of this drill, a side handle extension must be used to lengthen the side handle. The plastic bag that contains the hex wrench and the chuck key also contains the handle extension. Screw the extension firmly into the hole in the gear case of your drill and screw the side handle into the extension. DO NOT USE WITHOUT EXTENSION. Figure 3A SIDE HANDLE SIDE HANDLE EXTENSION Operation CAUTION: Always unplug the tool when attaching or changing bits or accessories. 1. Open the chuck jaws by turning collar with fingers and insert bit fully into the chuck. Tighten chuck collar by hand. Place chuck key in each of the three holes, and tighten in clockwise direction. It's important to tighten chuck with all three holes. To release bit, turn chuck key counter clockwise in just one hole, then loosen chuck by hand. 2. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power auger bits, or hole saws. For METAL, use h...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - 1338 (2.83 mb)
Дрели и шуропопверты - 1348 (2.83 mb)